Double round holder

If you want to go Buffalo hunting, the rule is you must buy a culling belt first. That tells your wife you are serious!! Nobody spends $250 on a culling belt unless they are serious about DG hunting!

Then you buy brass and bullets.

Then you load the ammo.

Then you decide on an outfit to hunt with.

Then you get the stalking boots (the Courteney boots arrived at the office today...wearing them to dinner).

Then you get the rifle.

Then you put down a deposit.

Then you put at least 300 rounds through said rifle.

etc, etc.

So yes, I am well on my way!
That is all together too much planning just to put a few rounds down range! I am truly dizzy!!!
 
Better practice your Scotch consumption technique if you are gonna hang celebrating with me around the fire buddy! Lol

Not a chance in the world I would even consider trying to hang with you for 5 minutes!

Outta my league!
 
That is all together too much planning just to put a few rounds down range! I am truly dizzy!!!

See, it works!

The idea is that your wife tries to figure out what you are up to and she finally just gets dizzy and gives in!
 
gentlemen,

somebody mentioned a 2 round holder that goes on the wrist for a quick reload for a double. does anyone know who makes it or where to find one?
 
gentlemen,

somebody mentioned a 2 round holder that goes on the wrist for a quick reload for a double. does anyone know who makes it or where to find one?

Try this @1dirthawker

http://www.ebay.com/itm/Tourbon-Rif...rrier-Real-Leather-Wristband-22-/262346624269

Screen Shot 2017-09-23 at 10.42.04 AM.png
 
Came with my double o/u
Aluminum with two clips from an MAG belt riveted on
Simply drop them in and 'break them off'
Fun for the range but they fell out my pocket during a buffalo stalk involving a belly crawl. Probably just need to work on a better pocket or belt holder.

IMG_2708.JPG
IMG_2709.JPG
IMG_2710.JPG
IMG_2711.JPG
 
Last edited by a moderator:
Came with my double o/u
Aluminum with two clips from an MAG belt riveted on
Simply drop them in and 'break them off'
Fun for the range but they fell out my pocket during a buffalo stalk involving a belly crawl. Probably just need to work on a better pocket or belt holder.

That's what I've been looking for! Thanks very much
 
@norfolk shooter , a friend of mine adapted the plastic cartridge holder out off a factory Ammo box. It wasn't pretty but was functional.
This was for a double rifle shooting driven boar.
If you are look for a belt to carry ammo I suggest you look at "el molino del viento" on google. They are Spanish leather manufacturers. Or,if you are in Spain, El Cort Ingles stocks the range.

IMG_1962.JPG
IMG_0715.JPG
 
Last edited by a moderator:
Guys I have a lovely rigby culling belt. Let me get the double in my hands and see how I do
 
Show us how you do when you made yours.
I am pretty quick with mine! Think there are a few videos lying around
I will just waiting out on the brass so I can make up the clip sections. Mind you I have far too many projects on the go at the moment. :A Bang Head: Just wondered what are the black clips made of??
 
Last edited:
Amazon also has wrist ammo holders
 
What ever belt, slide or device you decide to use it's important to practice. I will out empty brass in my gun or snap caps and make dummy rounds for my belt or just go outside and use live ammo. In case you are about to chastise me for using live ammo I live in rural Vermont my nearest neighbor is far away.
As mentioned in an earlier post I have been using Murray Leather belts and slides. I shoot left handed and load with my right hand. I wear the slide in front and remove the shells from from right to left, when I get close to my intended target I will loosen or lift the shells slightly to make them easier to pull. The following series of pictures will show how I load my rifle. By holding them the way I do you can control the rounds and keep them parallel as they drop into the rifles chamber .
hope this helps.
3W4bTpN.jpg


l6TfCsY.jpg


9mjUGFX.jpg
 

Attachments

  • 3W4bTpN.jpg
    3W4bTpN.jpg
    327.7 KB · Views: 341
  • 9mjUGFX.jpg
    9mjUGFX.jpg
    215.5 KB · Views: 331
  • l6TfCsY.jpg
    l6TfCsY.jpg
    222 KB · Views: 307
What ever belt, slide or device you decide to use it's important to practice. I will out empty brass in my gun or snap caps and make dummy rounds for my belt or just go outside and use live ammo. In case you are about to chastise me for using live ammo I live in rural Vermont my nearest neighbor is far away.
As mentioned in an earlier post I have been using Murray Leather belts and slides. I shoot left handed and load with my right hand. I wear the slide in front and remove the shells from from right to left, when I get close to my intended target I will loosen or lift the shells slightly to make them easier to pull. The following series of pictures will show how I load my rifle. By holding them the way I do you can control the rounds and keep them parallel as they drop into the rifles chamber .
hope this helps.
3W4bTpN.jpg


l6TfCsY.jpg


9mjUGFX.jpg

Smart technique there. That's how I was thinking about drilling and getting quick it's like the CAS shotgun technique
 
I really love that you bought a culling belt and filled it with shells for a rifle you don't have yet! That is a man with a plan!

That's a man with vision!
 

Forum statistics

Threads
68,106
Messages
1,514,047
Members
150,457
Latest member
MuhammadUr
 

 

 

Latest profile posts

LRich wrote on Andrew62's profile.
Andrew, I commented that your on 375 H&H for sale was the fair price.

Like I commented, my classic stainless has the original 24” barrel.

Did you buy yours with the barrel already cut down to 21” or did you do it (or a gunsmith)?
Zim Fan wrote on Charlie64's profile.
You might have edited your post on the PH in the Bubye. I know the PH and is a wonderful person and a fmaily man and runs a succesful business in Zim and just doesn't want the attention that the internet offers, the ugly kind.
Andrew62 wrote on Imac45acp's profile.
Hello,

Am I reading your post correctly to say that the Tsavo rifle will be coming out with a composite stock later this year? I ask because I had been looking very hard for a Tsavo, but if there is going to be a composite stock model I will wait for that.

Thank you for your time,

Andrew
1r4rc wrote on Corylax18's profile.
Saw your post. Nice. Denver too. Genesee area (just off 70) if ever up this way. Alternatively, do you have a membership at GGC? Whatever, you'll have a wonderful time in Africa. Enjoy.
'68boy wrote on UNTAMED KNIVES's profile.
Did you get my info? I sent name and requested info today. Want to make sure you received it. I don’t need any serial number etc
 
Top