Sorry about the delay, I have been out for a few days. Put the same post up on AR but deleted it, got trashed by one of the mods. I did not follow policy there! My mistake. I will limit my postings to AH from now on.
No 8x68 reamer.
Duplicator and all the accessories, stock blanks, patterns not sold. There is a long thread on using the duplicator here on AH in the gunsmith area, I will find it and post the link. This is a fantastic machine for a serious stock maker, very sturdy and accurate. It is a three spindle machine: Will duplicate a right hand stock from a right hand pattern, or a left hand stock from a right hand pattern, or two identical stocks from either a right hand or left hand pattern, or a right hand stock from a left hand pattern, or just about any combination. Included with the duplicator will be over 30 nice Pacific Big Leaf maple blanks, 20 or more plain maple blanks for making patterns, several big Oregon Walnut slabs for making blanks, and 35 or so patterns. Plus tooling: Cutters and tracers to match, spare parts for the duplicator, spare drive belts. And a checkering cradle, a special "sanding cradle" with centers matching the duplicator (for hand finishing and sanding the stock). This is a big, heavy, powerful machine made for production use. With enough length for full length Mannlicher style stocks and muzzle loader stocks. Most of the blanks ae way oversize, giving plenty of room for cast off, pitch, and drop suitable for big bore iron sight rifles.
$10,000 for everything. Located in Port Angeles, Washington, USA. Will take a pickup and trailer to haul everything, too much stuff to fit into a pickup. Or a box truck. Will take a day to disassemble and load everything. I took the machine completely apart, sandblasted and painted, installed new bearings, all new wiring and controls. Both motors are reversible, mainly to balance cutting loads when carving a pair of stocks (both right and left hand roughing cutters included, many unused).
Powerful 220 volt motors, single phase:
Sanding cradle:
Checkering cradle:
I will make a list of the reamers, dies, and other groups of items and post, will take a few days.
I cannot ship any gun related items outside of the US due to our silly laws.
For the 9.3x62: One nice barrel with sights, a Lothar Walthar, it is the bottom barrel in the photo. Barrel band ramp not yet soldered on. The Sako 300 H&H barrel is also for sale. $350 for the 9.3 plus shipping, $250 for the 300 H&H plus shipping. Both barrels threaded for M98. I have several M98 actions also. And a 9,3x62 reamer and go gauge (Both new PTG) for $150. A used 300 H&H reamer for $75. I have another 9.3 barrel, unthreaded and un chambered, a Shilen No. 4, 28 inches, 12 inch twist, CrMo. $250 plus shipping.
Also two sets of 9.3x62 dies, numerous cases and bullets. Photos later.
I have several M98 actions, just for fun below is the 9.3x62 barrel hand screwed into a M98:
New never used 450 Ackley Magnum reamer. Also have several 458 barrels, a few threaded and chambered for 458 Win. (Easy rechamber to the 450 Ackley) and two or three unthreaded unchambered barrels, will have to count. Have dies and Norma basic brass.
Never used BBK action. In the "rough" needs hand work and polishing. Will make a dandy 450 Ackley rifle, big magazine capacity. Standard M98 receiver threads.
458 Lott: Two sets of dies, numerous cases and loaded rounds. A PTG chamber reamer with only one chamber cut.
416 Rigby: Lilja CrMo barrel, never chambered or threaded. Dies. Numerous cases. PTG chamber reamer and go gauge, one chamber cut.
400 Holland & Holland: A M98 action, barrel is threaded, chambered, installed, test fired. Action needs feeding work, etc. Cases formed from 416 Rem. Reloading dies made with the reamers. Finish and Resize reamer. Resize die is neck bushing type, only sizes the neck. Test fire data obtained with Oehler M43 system. Barrel is a cut rifled Krieger.
I will take more photos and post, will take a few days.