Pay It Forward-Free

[Nevada Mike]

7 X 61 S&H brass goes to gprippers.

6.5 X 55 Brass still available.

 

[Bullthrower338]

Up for grabs a new set of 1” Medium Height 1 piece Tally’s for Winchester M70.

 

[TroyF]

View attachment 488089
Up for grabs a new set of 1” Medium Height 1 piece Tally’s for Winchester M70.

I'll take them

 

[Bullthrower338]

I'll take them

They are yours @TroyF PM me your address

 

[TroyF]

They are yours @TroyF PM me your address

pm sent, thank you

 

[SkullKeeper]

...Next ! ....

 

[mdwest]

one for you gun tinkerers and/or smiths out there..

assorted mauser parts

LR Mauser bolt (stripped)
3x LR Mauser bolt shrouds with cocking pieces (1 has the flag safety with it.. the other 2 do not)
1x SR mauser bolt shroud with cocking piece
1x SR mauser cocking piece (in addition to the shroud/cocking piece combo above)

All are from military (not commercial) mausers of unknown origin... best guess is the LR stuff started life on a DWM or VZ24 (most of the guns I have built started life as one of these two) and the SR stuff came off of a M96..

My spare parts drawer is over flowing after building a half dozen or so rifles.. so.. if anyone is in need... let me know..

 

[Poisonslinger]

Well Gentlemen and ladies...

New member here. I really doubt I'll trade hunting elk in the western US mountains for hunting Africa - although someday a picture-safari is on the bucket list. I was searching for a place to sell or trade some old bullets I have been packing around... but this forum / idea is a better choice. These .458/450 A-Frames are more bullet than my 45-70 lever gun needs. So here for the asking are two full boxes of Swift A-Frames, .458 size and 450 grain. One box is open and the other is sealed - 100 pills total.

You just have to remember to send me a picture (or post it here) of anything that meets its maker from these! Good luck hunting.

 

[Woodcarver]

Wow, glad I was looking, I'll take the A-Frames please

Sending a PM

Edit to add- I will find something tomorrow that should be useful to someone. Thanks!

 

[Poisonslinger]

That was fast - Will consider them gone to Woodcarver! I'll check my mail.

 

[SkullKeeper]

Wow, glad I was looking, I'll take the A-Frames please

Sending a PM

Edit to add- I will find something tomorrow that should be useful to someone. Thanks!

Good snag - I wish I’d been looking ! Lol !

 

[Woodcarver]

Thanks for the A-Frames @Poisonslinger !

As that was a very generous Pay It Forward and greatly appreciated, I found these to reciprocate;
200- 7mm 156gr Norma Oryx
150- 30-06 milsurp once-fired brass, sized, cleaned, primer pocket swaged, trimmed, ready to load

 

[Berettaco]

@Woodcarver - I could use the 7mm oryx. Pm to follow as well as my contribution

 

[freefall]

Woodcarver, nice offering on the bullets and brass. Unfortunately I don't have an 06 at present or I'd be on that brass like ugly on an ape!

 

[Woodcarver]

The Oryx are yours @Berettaco I'll get them headed towards MO in the next day or so!

 

[SkullKeeper]

This thread is on a roll today !

 

[Berettaco]

Ok - here’s my contribution to whomever can use them - I’ll cover shipping to the US.
2 packs of .50 powerbelt 325 gr
1 pack of .50 powerbelt 295 gr
1 pack of .50 powerbelt 295 gr HP
1 set of new talley 30mm rings (blued)

 

[TroyF]

Ok - here’s my contribution to whomever can use them - I’ll cover shipping to the US.
2 packs of .50 powerbelt 325 gr
1 pack of .50 powerbelt 295 gr
1 pack of .50 powerbelt 295 gr HP
1 set of new talley 30mm rings (blued)View attachment 491104

If those are the Talley for the Talley bases I could them for my 9.3x62 build.

I need to look around for some good stuff to pif.

 

[Berettaco]

If those are the Talley for the Talley bases I could them for my 9.3x62 build.

I need to look around for some good stuff to pif.

Yes - Talley rings for Talley bases

 

[TroyF]

Yes - Talley rings for Talley bases

Ok cool if take them if not spoken for.