Rank the Solids

I’ve had success with Cutting Edge and Barnes Banded solids. Obviously, you should shoot what regulates best in your double.
 
Hard to top the performance of a machined solid assuming you're not putting them in an old double rifle.

I've read that flat nose is better then round nose and depressed noses like the Woodleigh Hydro's create the biggest wound channel with the straightest line penetration.

Hard not to listen to the pros on this one and shoot the best you can get your hands on when your life might depend on its performance.
 
I only had experience with the Woodleigh Hydrosolids. Wicked cruel on my Cape Buffalo. It just shuddered and dropped
 
That sounds decisive!! The flat point Barnes Banded Solids should do almost as well as the Hydrostabilized solids.
 
I only had experience with the Woodleigh Hydrosolids. Wicked cruel on my Cape Buffalo. It just shuddered and dropped
What calibre rifle? And why did you decide to use solids over preferred softs?
 
What calibre rifle? And why did you decide to use solids over preferred softs?
Woodleigh Hydro solids (and Swift"s new solid) are half way between a solid and a hollow point. The theory is the cupped point will generate a pressure wave ahead of the bullet, dealing additional flesh damage.

North Fork also makes a cupped point solid. But theirs is a bit more like a true "hollow point" bullet.

Again though... I dont know why there is so much discussion in this thread. You do not get to pick your projectiles with a double rifle like you do with a bolt action rifle. Anyone with experience loading for doubles will tell you, they are very picky when it comes to bullet selection. The gun will only truly regulate with the bullet it was originally built for and perhaps other very similar bullets. If the gun was set up with traditional solids than it is unlikely it will work properly with more modern brass/copper bullets.
 
Woodleigh Hydro solids (and Swift"s new solid) are half way between a solid and a hollow point. The theory is the cupped point will generate a pressure wave ahead of the bullet, dealing additional flesh damage.

North Fork also makes a cupped point solid. But theirs is a bit more like a true "hollow point" bullet.

Again though... I dont know why there is so much discussion in this thread. You do not get to pick your projectiles with a double rifle like you do with a bolt action rifle. Anyone with experience loading for doubles will tell you, they are very picky when it comes to bullet selection. The gun will only truly regulate with the bullet it was originally built for and perhaps other very similar bullets. If the gun was set up with traditional solids than it is unlikely it will work properly with more modern brass/copper bullets.
I don’t know because I have not used all of them, but ones I have used Hornady, NF CPS, Woodleigh softs, they all group close. Now I don’t go for 1 -2 MOA, at 50 or 100, As long as they r within 3-5 in at 50 I’m good.
 
Maybe I’m just lucky, but my 470 NE seems to shoot several different projectiles well. Currently prefer CEB 500gr. And with a half grain drop in powder their Raptors and Barnes TSX shoot to the same point.
 
IMG_7062.jpeg
 
Maybe I’m just lucky, but my 470 NE seems to shoot several different projectiles well. Currently prefer CEB 500gr. And with a half grain drop in powder their Raptors and Barnes TSX shoot to the same point.
What powder and how many grains?
 
I’m running 83gr of Reloader 15.5 behind the CEB 500gr solid. Speeds are right at 2100fps.
 
Maybe I’m just lucky, but my 470 NE seems to shoot several different projectiles well. Currently prefer CEB 500gr. And with a half grain drop in powder their Raptors and Barnes TSX shoot to the same point.
It varies from gun to gun and depends on what ammunition the gun was originally regulated with.
 
It varies from gun to gun and depends on what ammunition the gun was originally regulated with.
My gun was regulated with Norma PH softs. I opened one measured the powder and use it to regulate, it has woodlegh softs
 

Forum statistics

Threads
65,396
Messages
1,443,315
Members
135,865
Latest member
Petrket
 

 

 

Latest posts

Latest profile posts

'68boy wrote on Rare Breed's profile.
Wife and I will attend ah dinner in Nashville Friday night. Jay Sheets and wife Chris
crossfire3006 wrote on Hornedfrogbbq's profile.
An excellent AH member right here! I had a fantastic transaction with Hornedfrogbbq (I was the seller). His communication was first rate, payment was extremely fast, and I would have absolutely no reservations at all dealing with him again. Thank you, F!
Here we are, the last day of the show in Denver, it's been a good show but expecting a quiet day today. I will be back for-sure to do this show next year and maybe also do the one in Sacramento California.

On Monday I will be hitting the road driving from Denver and eventually make it down to Atlanta for the flight home.

its going to be a good year!
CraigV wrote on Rem280's profile.
Hi Rem280, Saw your post on getting selected for Idaho Elk. Do you have a zone(s) selected? I live in N Idaho, might be able to offer some ideas.

Cheers,

Craig
ghay wrote on Konrad.inc's profile.
Do you still have the Ruger 9.3x62?
 
Top