458 Win Mag comparison to its peers-375,416,404

Nhoro

AH fanatic
Joined
Sep 16, 2014
Messages
880
Reaction score
1,498
Location
Harare,Zimbabwe
Media
26
Member of
Cleveland Gun Club
Hunted
Zimbabwe
Hi All,

The debate has raged about the 458 win mag for years and I just wanted to cut through the bull doo doo and try to compare some well loved calibres and the math behind their reputation. In the picture below, I have put down some facts and figures that are used to compare ballistics performance and then done some sums with those.Sorry it is all metric but I have put in the imperial units next door for most. Most columns are self explanatory but I have done a column of energy per mm2 of cross sectional area. My theory is that energy is what does the penetrating and X sectional area is a measure of the resistance to penetration ie the size of the hole / the energy available to make the hole. It just allows a comparison of different calibres.

So here are my comments:
1/ 450 gr bullets from a 458 have the same sectional density as a 300 gr .375 bullet and have more energy per x sectional area than a 404 J. Maths suggests penetration would be in between those two ie less than 375 but more than 404 J.
2/ 458 win mag 500 gr at 1900 fps has significantly less energy per x sectional area than any of the others -30 to 40 %. This puts a number to the old stories from elephant culls etc. 30 -40 % less penetration would be a problem.
3/ Full power 458 win mag bullets are comfortably between 404 J and 375/416 in energy per x sectional area. That would suggest the penetration is between those.
4/ 375 and 416 rigby are highest in energy/xsectional area and in reputation for good penetration.

Conclusion: This figure of energy per Xsecetional area seems to predict penetration quite well and follows all the well known opinions. So I think the 458 win mag with 450 gr is a real option for dangerous game and the 480 and 500 gr are even better. The numbers put it right in the middle of well respected calibres, between the 404 and 375/416. Let the games begin !

Calibre comparison.png
 
Last edited by a moderator:
Interesting and thanks for putting in the effort.

Have done no such computations, but our experience with 450 grain .458 bullets at 2150 fps on buff and ele match your calculations.
 
Good numbers you have there, but it remains a fact that the 458LOTT lived up to the hype that the 458WM claimed...and never obtained.
Althought the recoil of the 458LOTT is more in line with the 470NE, I would still consider it a contemporary of the 458WM.
 
Good numbers you have there, but it remains a fact that the 458LOTT lived up to the hype that the 458WM claimed...and never obtained.
Althought the recoil of the 458LOTT is more in line with the 470NE, I would still consider it a contemporary of the 458WM.
Interesting observations. In theory,recoil from the 470 should be the same as the win mag. Same bullet at the same velocity. Most people put the Lott a bit higher.. but so much depends on the rifle. I have fired a 500 NE that is more comfortable than my 458 win mag. But it weighs several pounds more !
 
I am not very well read on ballistics , however l may only give my personal experience with the matter. When l was a professional Shikari in Darjeeling , India from 1962 to 1970 , the only calibres brought by clients for shooting thick skinned animals ( namely Gaur , or Indian Bison ) were the 9.3 millimeter cartridge by mauser , the magnum .375 by Holland and Holland and the magnum .458 by Winchester. In regards to the magnum .458 by Winchester , l will give two incidents . One good and one bad.
Screenshot_20191006-203431_01_01.png

This Gaur weighed in the ambit of 2000 pounds and was killed by my client who used a double barrel rifle calibrated for magnum .458 by Winchester made by the firm , Holland and Holland. It worked splendidly on the creature , using one soft head 510 grain bullet and one 500 grain metal envelope blunt head solid bullet ( from firm , Winchester ).

However , l had one other client who also went for a Gaur Shikar with us and he carried a magnum .458 Winchester caliber bolt operation rifle made by the firm , Birmingham Small Arms which used 500 grain metal envelope bullets from the firm , Hornady. We almost lost our lives in this incident and the full account of that incident can be read in an article l have written here , called " The Gaur Shikar which went very terribly wrong " and photographs of that incident also.
I personally never had hesitation guiding clients who would bring magnum .458 Winchester rifle to Shikar.
However , my former Shikar partner was very apprehensive of this cartridge. In his view , he compared it to the magnum .375 cartridge and always believed that if the .375 cartridge has a 76 millimeter case of powder to propell a 300 grain bullet , then the .458 which used a 500 grain bullet ( 200 grains heavier ) should have a case at least as large ( if not larger ) than a .375 to accommodate a correspondingly large charge of powder.
But please do not treat our view as gospel , because we were just two young men at the time who were not very well read about mathematical ballistics values and merely made judgements from what we observed . Also , much has changed in the five decades l have been retired . I
hope l was of assistance .
 
you're losing me a bit in the explanation.
I feel as though the Indian gentleman's anecdote is working its way around toward being a proponent of the Lott over the standard .458. The proportionality of the case to the projectile and the powder charge and it all makes a great deal of sense. It's a quite simple manner of gauging penetration potential. What he's saying is correct in that the .458 should have a larger powder charge to propel a bullet such as a 500 grainer. Nothing in ballistics is free, except for the 6.5 Creedmore....joking. The one man is 50/50 on the .458 and the other found it lacking based on case volume is what I got out of it.
 
I feel as though the Indian gentleman's anecdote is working its way around toward being a proponent of the Lott over the standard .458. The proportionality of the case to the projectile and the powder charge and it all makes a great deal of sense. It's a quite simple manner of gauging penetration potential. What he's saying is correct in that the .458 should have a larger powder charge to propel a bullet such as a 500 grainer. Nothing in ballistics is free, except for the 6.5 Creedmore....joking. The one man is 50/50 on the .458 and the other found it lacking based on case volume is what I got out of it.
Forrest Haley
That is very accurate. Thank you for helping to organize my words with better English and scientific analysis.
 
Energy/mm2 is too favorable, imho, to fast calibers and doesn’t give justice to the .404.
If you extend the calculation to .378wm, or .460wm, you will of course show very high ratios for them, way higher than the good old proven .404... way higher than their value on the field.

I believe in sectional density, don’t take me wrong. Mass is important.
As of speed: I think there is a soft spot on speed reached by the .404, or the .416, and the .458 Lott that makes them the classical they are, for good reasons. The .375 needs a bit more boost but it’s not a stopping caliber anyway.
Higher speed than that only brings more recoil, blast, issues with bullets not conceived for that..
 
  • Like
Reactions: IvW
Seems to me the properties of a cartridge are measured: frontal area, mass per square inch, millimeter of frontal area, ratio of frontal area to mass, and momentum. As noted previously, I got lost in the listings and didn't see a way of reducing the information down to these basics.
 
To grasp full concepts involved, the difference between (kinetic) energy and momentum must be understood. The points about the relationship between frontal area and mass are well taken and can be applied to the original premise (comparing the 458 to other cals)... in basic terms.
 
All BS and cartridge and rifle favoritism aside, it still boils down to the bullet, velocity, and accurate shooting.
The pro and con debates were fun at the start but became tiresome years ago.

Even my old, underpowered 1886 .45-90 can muster up enough energy to push a 450 grain NF solid to 2150 fps MV and kill any big game extant. Only bragging rights are the dead animals.
 
Last edited:
The .458 Win Mag is still one of the most popular dangerous-game cartridges in spite of the (in my opinion) flawed premises on which it was originally designed. As we all know, Winchester wanted to duplicate the ballistics of the big British nitro expresses with a cartridge that would fit a .30-06 length action. They therefore trimmed down a .375 H&H case, blew it out to .458 and used a compressed load to push a 500-510 grain bullet above the 2,000-fps mark. The compressed load gave them problems, so they quietly loaded down the powder charge, causing a loss in velocity and, in some tragic cases, performance on the big nasty stuff that can hit back.

Why they didn't do right away what Jack Lott did eventually--i.e., use a full-length .375 H&H as the parent case--is still a mystery to me. Sure, today with modern powders the originally-intended ballistics can be achieved, but the shorter case of the .458 Win precludes the use of some of the longer, more hi-tech bullets available today.

So unless I had a special place in my heart for the .458 Win Mag or for a specific rifle for which it--and it alone--is chambered, I wouldn't choose it. The various .416s, the older .500s, the .458 Lott and, of course, the old standby .375 H&H are very valid alternatives to it.
 
Why they didn't do right away what Jack Lott did eventually--i.e., use a full-length .375 H&H as the parent case--is still a mystery to me.

I believe it was the marketing logic in use today by crack dealers. The pipe and first hit are free. Then those foolish to smoke that poison are addicted for life, albeit a rather short one once addicted.

For Winchester, there was more money in standard length ammunition than in marketing an extra long round. Let other gun makers chamber rifles for the standard length .458 Win and sell ammo, ammo, ammo. At least, it seems that was their plan...
 
...I'm gonna' respond in a way I trust no one gets his/her panties in a wad. First of all, I have had the opportunity to shoot a "goodly" number of elephant on control. I've killed elephant utilizing the following cartridges:

.416 Taylor, .458 WM, .450 Rigby and .505 Gibbs. The Taylor and WM are M-70s, the Rigby was a Ruger RSM, and the Gibbs was a Granite Mountain Arms

Conventional wisdom would almost certainly have the Gibbs as the forerunner "best in class" for dealing with elephant. Indeed, the Gibbs is all it's touted to be. If I were a p/h (and could afford one) the Gibbs would be my preferred back up rifle.

The .450 Rigby is what the Lott should have been. You know, 2450fps as opposed to 2250fps. More velocity is better...right? HA!

The .458 WM will always have its nay sayers, blah, blah and blah.

The .416 Taylor, or any 40cal is far and away better than the .375 H&H. Unless you're Harry Manners.

All the elephant I shot with these four calibers were killed. Obviously, the ones brain shot dropped in their tracks. Body shots to the heart/lungs, most didn't run more than 50-60 yds before succumbing.

After evaluating the type shooting in which I was involved, any one of the calibers were adequate to achieve the end result.

The amount of empirical experience I have is limited by the total number I have successfully shot/killed. (If you're interested in the number, well, it is 12% of the total John Buhmiller shot)

Regardless of graphs, and old history, and SD, and BC, and fps...I chose the "worthless. underpowered, should have been, etc,etc" .458 Winchester Magnum. I've never felt under gunned. My rifle is a Winchester M-70 with a 24" barrel.
Loads are: 500gr solids @ 2185fps.

If it ain't broke, don't fix it
 
...my apologies to the OP for hijacking his thread. This response should've been on "Another 458 Win Mag Thread."

I have zero expeience with the .404, and limited experience with the .375. Next time before typing, I'll RTFQ.
 
Hi All,

The debate has raged about the 458 win mag for years and I just wanted to cut through the bull doo doo and try to compare some well loved calibres and the math behind their reputation. In the picture below, I have put down some facts and figures that are used to compare ballistics performance and then done some sums with those.Sorry it is all metric but I have put in the imperial units next door for most. Most columns are self explanatory but I have done a column of energy per mm2 of cross sectional area. My theory is that energy is what does the penetrating and X sectional area is a measure of the resistance to penetration ie the size of the hole / the energy available to make the hole. It just allows a comparison of different calibres.

So here are my comments:
1/ 450 gr bullets from a 458 have the same sectional density as a 300 gr .375 bullet and have more energy per x sectional area than a 404 J. Maths suggests penetration would be in between those two ie less than 375 but more than 404 J.
2/ 458 win mag 500 gr at 1900 fps has significantly less energy per x sectional area than any of the others -30 to 40 %. This puts a number to the old stories from elephant culls etc. 30 -40 % less penetration would be a problem.
3/ Full power 458 win mag bullets are comfortably between 404 J and 375/416 in energy per x sectional area. That would suggest the penetration is between those.
4/ 375 and 416 rigby are highest in energy/xsectional area and in reputation for good penetration.

Conclusion: This figure of energy per Xsecetional area seems to predict penetration quite well and follows all the well known opinions. So I think the 458 win mag with 450 gr is a real option for dangerous game and the 480 and 500 gr are even better. The numbers put it right in the middle of well respected calibres, between the 404 and 375/416. Let the games begin !

View attachment 309093
I just can’t help it…I do not like the 458 caliber at all. Do an experiment with me…go onto GB and GI and see what is the most for sale caliber bolt action gun…correct answer…the 458
 
I just can’t help it…I do not like the 458 caliber at all. Do an experiment with me…go onto GB and GI and see what is the most for sale caliber bolt action gun…correct answer…the 458

Huh???
 

Forum statistics

Threads
53,653
Messages
1,132,115
Members
92,757
Latest member
ramenbetConsuelo
 

 

 

Latest posts

Latest profile posts

Houston Bill wrote on Sketchy1973's profile.
Hello,

I am considering selling my Rizzini 470 NE double, if you have interest we should discuss.

Bill
btheis13 wrote on migrabill's profile.
I love your zebra avatar! Is that yours? If so, would you mind sharing who did your taxidermy work?
Impact shots from the last hunt

Early morning Impala hunt, previous link was wrong video

 
Top