Rifle barrels that will withstand a barrel burner caliber - 6.5X68S

Gert,

Maybe tell us how many rounds you would like to get out of your barrel. We can help make suggestions on rounds that meet that requirement.
 
gert,
12 barrels of 6.5/284 have given between 900 and 1200 shots of barrel life on the rifle range.
a 6mm on that case would be worse.
hunting would not be as hard on a barrel, as it would not get as hot.
the straight 284 seems to give about 2400 shots on the rifle range, a significant improvement.
the difference between the range and hunting is that you have time to adjust your elevation setting on the range.
therefore on the range flat trajectory is not as important.
when hunting, flatter trajectory offers a longer point blank range, and a cartridge should be selected on this basis as to the conditions you shoot in, and the reality of your ability as you sensibly suggest.
on the range, you only have to poke a hole in a piece of paper or ring steel so power and trajectory are less important.
the 284 win or the 280 rem would work well on the range with reasonable barrel life, while still being useful in the field.
bruce.
Bruce at what point are you calling a barrel burnt out. What size of group at 100 yds do you consider no good.
 
Bruce/Inline much appreciated ...Am I correct if I use a heavy for caliber bullet in the 6.5x68S to get a longer life from the barrel..I will not shoot light bullets ..I like to use the most weighted bullet possible for the 6.5x68S caliber...this will be to my advantage when shooting in the wind???all shooting /hunting will be as a hunter ..at the shooting club as well..We shoot twice a month..each table we shoot is about five rounds at 300 meters( three minutes) , then walk to the 150 meter ( five bullets three minutes ) walk to the 50 meters shoot (three minutes )
I only shoot one tabel...Hunting is twice a year ..I do not think I will use it to hunt since I do bush veld hunting..walk/stalk on foot...with my other calibers..
 
What size targets are we talking about?

I like the 130s in a 6.5, they have a good bc and you take less recoil. Depending upon target size at 300 yards wind would really have to be getting it to push you off target.
 
graham,
those barrels were in an fclass rifle.
for that competition you really need better than 1/2 moa.
however very few rifles will do that for 20 shots, contrary to urban myth.
we see so many reports of 1/2 moa rifles that I wonder why people use custom gunsmiths , custom barrels, custom actions, and sophisticated reloading techniques.
it so often turns out that some guy jagged a lucky 3 shot group, and assumes his rifle is a 1/2 moa performer.
in my case I can still shoot fclass at club level when a barrel goes out to 1 moa, and you can see this from plot sheets.
at longer ranges it is vertical in the group you have to go by, as wind deflection has more scope for human error.
by this stage you have chased the throat with seating depth, and adjusted powder charges accordingly, until such things do not help any more.
looking at those throats with a bore scope answers all the questions.
sometimes if you get it early enough, a rechamber will give a bit more life to a barrel, but on a hunting rifle barrel this is often not possible due to barrel external dimensions.
you might say these barrels will still be useful for hunting accuracy wise, and you would be right, but not for many more shots.
I have also had this in rifles used for serious culling.
accuracy will drop off some, and can the just go away completely.
you do not want to be in the field when that happens.
bruce.
 
graham,
those barrels were in an fclass rifle.
for that competition you really need better than 1/2 moa.
however very few rifles will do that for 20 shots, contrary to urban myth.
we see so many reports of 1/2 moa rifles that I wonder why people use custom gunsmiths , custom barrels, custom actions, and sophisticated reloading techniques.
it so often turns out that some guy jagged a lucky 3 shot group, and assumes his rifle is a 1/2 moa performer.
in my case I can still shoot fclass at club level when a barrel goes out to 1 moa, and you can see this from plot sheets.
at longer ranges it is vertical in the group you have to go by, as wind deflection has more scope for human error.
by this stage you have chased the throat with seating depth, and adjusted powder charges accordingly, until such things do not help any more.
looking at those throats with a bore scope answers all the questions.
sometimes if you get it early enough, a rechamber will give a bit more life to a barrel, but on a hunting rifle barrel this is often not possible due to barrel external dimensions.
you might say these barrels will still be useful for hunting accuracy wise, and you would be right, but not for many more shots.
I have also had this in rifles used for serious culling.
accuracy will drop off some, and can the just go away completely.
you do not want to be in the field when that happens.
bruce.
Thanks Bruce. I was just trying to see what scenario we were looking at. I have burnt out several bbls. But at a much higher round count than you were indicating. But the requirements of group size were more than F class. On this forum I am just trying to be practical on 300 to maybe 400yds if the shooter has the ability to shoot accurately at those distances. Thanks again for answering my question.
 
graham,
those barrels went faster than a hunting barrel, due to rate of fire and lengths of strings.
I would still like moa barrels/rifles for hunting the ranges you mention.
I moa is 4" at 400, so adding shooter error and trajectory into a point blank scenario the shooter would still need to be a very good shot and there be very little wind.
bruce.
 
graham,
those barrels went faster than a hunting barrel, due to rate of fire and lengths of strings.
I would still like moa barrels/rifles for hunting the ranges you mention.
I moa is 4" at 400, so adding shooter error and trajectory into a point blank scenario the shooter would still need to be a very good shot and there be very little wind.
bruce.
Absolutely agree Bruce!
 
I find a lot of the claptrap about 1 shot kills at 1 mile+ by military snipers a bit interesting.
a 1 moa rifle (possibly optimistic) would shoot 17.6" at 1 mile if it holds that accuracy to that distance.
add on some shooter error.
add on target movement both up and down and left and right due to mirage.
add on muzzle velocity variation (be aware that 10fps difference is noticeable at 1000 yds, and military ammo would not come close to 10 fps)
add on wind deflection .( there is no way of measuring wind speed all the way to the target, and at the various heights of trajectory)
add on the wind conditions can and do change during time of flight.
any hit is a lucky one:Wideyed:
strangely many hunters believe the stories and assume such things can also be done on game.
this suggests nil experience with long range shooting.
many of the same shooters take no account of what is required in terminal ballistics for the job in hand.
if they had an inkling of the inhumane results of such so called hunting they might not do it.:A Bang Head:
bruce.
 
I find a lot of the claptrap about 1 shot kills at 1 mile+ by military snipers a bit interesting.
a 1 moa rifle (possibly optimistic) would shoot 17.6" at 1 mile if it holds that accuracy to that distance.
add on some shooter error.
add on target movement both up and down and left and right due to mirage.
add on muzzle velocity variation (be aware that 10fps difference is noticeable at 1000 yds, and military ammo would not come close to 10 fps)
add on wind deflection .( there is no way of measuring wind speed all the way to the target, and at the various heights of trajectory)
add on the wind conditions can and do change during time of flight.
any hit is a lucky one:Wideyed:
strangely many hunters believe the stories and assume such things can also be done on game.
this suggests nil experience with long range shooting.
many of the same shooters take no account of what is required in terminal ballistics for the job in hand.
if they had an inkling of the inhumane results of such so called hunting they might not do it.:A Bang Head:
bruce.
Personally I won't watch the long range (hunting) shows. I know one cameraman who quit after getting tired of seeing animals shot multiple times or wounded and lost. The other thing to the long range sniper is the time it takes for a bullet to travel a mile or more. I forget the exact number of seconds but it was more than enough time to bend over to tie your shoelace or step out of the way.
 
I find a lot of the claptrap about 1 shot kills at 1 mile+ by military snipers a bit interesting.
a 1 moa rifle (possibly optimistic) would shoot 17.6" at 1 mile if it holds that accuracy to that distance.
add on some shooter error.
add on target movement both up and down and left and right due to mirage.
add on muzzle velocity variation (be aware that 10fps difference is noticeable at 1000 yds, and military ammo would not come close to 10 fps)
add on wind deflection .( there is no way of measuring wind speed all the way to the target, and at the various heights of trajectory)
add on the wind conditions can and do change during time of flight.
any hit is a lucky one:Wideyed:
strangely many hunters believe the stories and assume such things can also be done on game.
this suggests nil experience with long range shooting.
many of the same shooters take no account of what is required in terminal ballistics for the job in hand.
if they had an inkling of the inhumane results of such so called hunting they might not do it.:A Bang Head:
bruce.

Bruce,

I enjoy reading what you write, it obviously you know what you are doing.

I'm not a Sniper I don't have that skill set. I do squeeze a trigger every now and then. I have center punched targets (1/2 moa) at a mile cold bore. I have also missed 4'X4' targets at 1500 yards after shooting most of the day (due to wind and mirage). I have shot 3/8" ( not MOA) at 300 yards (5 shots) and have miss 10" plates at 500 yards. The miss at 500 yards was due to adjusting the magnification ring on the scope move it from 15X to 25X caused an impact shift. I have shot over targets due to light conditions. The more you shoot the more you see. I test gear out if it does not perform I send it down the road. I like stretching it out, the better you hit at distance the better you hit up close.

I have people ask me how far can you shoot a deer, my response is always the same. What are the conditions...it's about knowing what you and your system are capable of.
 
good post inline6.
it is obvious you have done enough to realize that at long range, sometimes you get the chicken and sometimes you get the feathers.
it is up to us to guarantee the chicken each and every time, and that means being honest with yourself.
bruce.
 
Last edited:
graham,
those barrels went faster than a hunting barrel, due to rate of fire and lengths of strings.
I would still like moa barrels/rifles for hunting the ranges you mention.
I moa is 4" at 400, so adding shooter error and trajectory into a point blank scenario the shooter would still need to be a very good shot and there be very little wind.
bruce.

Thank you Bruce, maybe you are the person whom I need to explain in a clear, simple manner the following term so I can understand MOA long distance term:
I moa is 4" at 400
 
Bruce,

I enjoy reading what you write, it obviously you know what you are doing.

I'm not a Sniper I don't have that skill set. I do squeeze a trigger every now and then. I have center punched targets (1/2 moa) at a mile cold bore. I have also missed 4'X4' targets at 1500 yards after shooting most of the day (due to wind and mirage). I have shot 3/8" ( not MOA) at 300 yards (5 shots) and have miss 10" plates at 500 yards. The miss at 500 yards was due to adjusting the magnification ring on the scope move it from 15X to 25X caused an impact shift. I have shot over targets due to light conditions. The more you shoot the more you see. I test gear out if it does not perform I send it down the road. I like stretching it out, the better you hit at distance the better you hit up close.

I have people ask me how far can you shoot a deer, my response is always the same. What are the conditions...it's about knowing what you and your system are capable of.
Inline, great post and a lot of good sense information...your advice would serve a lot of hunters on good stead...I have found for myself (I am not shooting long distance ) if I start practicing shooting my compound bow for a month before a hunt..I really have a much better sight picture at a rifle target and better grouping...I used to practice at 80 meters with my compound bow back to fifteen meters....my breathing stabilize and ensure better accuracy...(y)(y)
 
Not to stray from this great informative discussion. ...long range shooting scenarios, barrel life, methods to improve barrel life , target barrel life versus hunting barrel life, heat erosion in rifle chamber leading to increased/faster shooting out of barrels has been covered...can we focus for a while on bullets /bullet selection for these barrel burners, bringing in account the importance of SD as well as BC when shooting these bullets in the 6.5 x 68S barrel burner caliber...
Here is a link to a type of hunting bullet..do you members care to reply on this video?
https://www.hornady.com/ammunition/rifle/6-5-creedmoor-143-gr-eld-x-precision-hunter#!/
 

Attachments

  • Screen Shot 2019-05-01 at 9.44.02 AM.png
    Screen Shot 2019-05-01 at 9.44.02 AM.png
    2.9 MB · Views: 97
  • Screen Shot 2019-05-01 at 9.44.04 AM.png
    Screen Shot 2019-05-01 at 9.44.04 AM.png
    1.8 MB · Views: 102
  • Screen Shot 2019-05-01 at 9.44.09 AM.png
    Screen Shot 2019-05-01 at 9.44.09 AM.png
    1.5 MB · Views: 97
  • Screen Shot 2019-05-01 at 9.44.11 AM.png
    Screen Shot 2019-05-01 at 9.44.11 AM.png
    804.5 KB · Views: 90
  • Screen Shot 2019-05-01 at 9.44.14 AM.png
    Screen Shot 2019-05-01 at 9.44.14 AM.png
    463.8 KB · Views: 95
gert,
1 minute of angle is the angle the earth turns in 1 minute.
there are 60 minutes in 1 degree.
it just happens that this angle is very close to 1" at a distance of 100 yds
so 1 moa = 1" at 100 yds, 2 moa = 2" at 100 yds, 3 moa = 3" at 300 yds.
2 moa = 2" at 100 yds, 2 moa = 4" at 200 yds, 3 moa = 6" at 300 yds.
1/2 moa = 1/2' at 100 yds, 1" at 200 yds, 1.5" at 300yds.
measure group size in inches and divide by (range divided by 100) to get moa.
e.g. you have just sot a 12" group at 500 yds.
500 divided by 100 = 5
12 divided by 5 = 2.4 moa.
going into the mildot type scopes is confusing in this conversation other than to sy that moa type scopes are more useful to both hunters and target shooters due primarily to the fact that the adjustments on moa scopes are finer.
milradians are suited to military where wounding is to be preferred to killing.
bruce
 
b.c. (ballistic coefficient) is a measure of slipperiness of a bullet through air relative to a standard bullet.
the standard bullet in a g1 b.c. is different to the standard bullet in the g7 model.
gi is used for flat base, and g7 for boat tails.
the two come close in application, but not exactly the same when applied to a ballistic calculator like jbm calculations.
suffice it to say that the higher the number, the more slippery is the bullet.
more slippery means a lower percentage of muzzle velocity is lost due to drag, translating into less wind deflection.
note the word deflection. there is no such thing as wind drift.
if shooting longer ranges, high b.c. bullets are an advantage in the wind as well as retaining energy.
one issue with high b.c. bullets is that many of them are suited more for target shooting and less for terminal performance.
sometimes a compromise needs to be made here.
s.d. ( standard deviation) is a form of statistical measurement.
a mathematician can easily describe it better than me, but in essence it is a way of presenting an average value of a group of things.
if you want consistency, the lower the s.d. the better.
probably the 2 areas to most interest shooters are in weights and velocities.
lower s.d in bullet weights, charge weights, case weights, etc. aid in ammunition consistency.
the big one is velocity s.d.
the lower this is, the pore shots in the sample will be nearer the verticle centre of the group.
and probably the group in general as well, because the barrel is more likely to be nearer the same point in its oscillation as the bullet exits.
some prefer to use extreme spread, e.s., rather than s.d.
where this argument fails is that e.s. is a measure of 2 samples only, e.g. highest and lowest.
s.d. is a measure of all samples and takes them all into account.
bruce.
 
please excuse multiple threads, but combining them could make it harder.
shooting longer high b.c. bullets requires sufficient twist for stability.
generally a gyroscopic stability (sG) of 1.5 is recommended, but at long range with long bullets going a little higher (say up to 1.8) can be of benefit.
this is in part due to a thing called wind shear, when a bullet goes from one condition to another in its flight, be it wind speeds, directions or both.
the changing forces on the bullet can cause it to wobble, enlarging the group.
bruce.
 
can't edit the post re b.c. and s.d.
most things in shooting are statistical, rather than empirical.
you need to take a lot of samples and compare them
with s.d., say you are measuring velocities, s.d. is not meaningful for less than 10 shots, and more is better..
bruce.
 

Attachments

  • Screen Shot 2019-05-01 at 9.45.05 AM.png
    Screen Shot 2019-05-01 at 9.45.05 AM.png
    845.3 KB · Views: 97
  • Screen Shot 2019-05-01 at 9.45.07 AM.png
    Screen Shot 2019-05-01 at 9.45.07 AM.png
    361.5 KB · Views: 93

Forum statistics

Threads
53,632
Messages
1,131,575
Members
92,696
Latest member
stitchcart
 

 

 

Latest posts

Latest profile posts

Early morning Impala hunt, previous link was wrong video

Headshot on jackal this morning

Mature Eland Bull taken in Tanzania, at 100 yards, with 375 H&H, 300gr, Federal Premium Expanding bullet.

20231012_145809~2.jpg
 
Top