Wanted Lee factory Crimp Die For 416 Rigby

[SkullKeeper]

Hopefully someone will have a Lee factory crimp die for a 416 Rigby. I sure need one.

 

[MMAL]

Lee will make you one custom. Just be sure that the custom die is the right size for your press. I had them make a 500/416 custom for me which they did in a larger diameter. It did not fit my Hornady due and needed to buy, surprise surprise a Lee press. I actually like it better. Love those crimp dies.

 

[SkullKeeper]

Lee will make you one custom. Just be sure that the custom die is the right size for your press. I had them make a 500/416 custom for me which they did in a larger diameter. It did not fit my Hornady due and needed to buy, surprise surprise a Lee press. I actually like it better. Love those crimp dies.

Thank you very much for the suggestion - I will contact them Monday !

 

[double rifle newbie]

i reload for my 450 NE with Lee dies. They dont carry this caliber in regular stock. i contacted them and they happily made me a custom set of dies. i had to send them one brass that had been fired. turnaround time was pretty quick. a couple of weeks.

 

[fourfive8]

According to their website, their custom services have been suspended for a while now (since April 20, 2020)- due to demand surge, covid excuse, etc. Contact them to to verify.

Lee Precision, Inc.. Custom Services

Custom service ordering area. Order custom bullet molds, custom case length gauges and custom die sets.

leeprecision.com

 

[double rifle newbie]

According to their website, their custom services have been suspended for a while now- due to demand surge, covid excuse, etc. Contact them to to verify.

Lee Precision, Inc.. Custom Services

Custom service ordering area. Order custom bullet molds, custom case length gauges and custom die sets.

leeprecision.com

oh man. bad break. hopefully they will crank up the custom shop soon.

 

[SkullKeeper]

According to their website, their custom services have been suspended for a while now (since April 20, 2020)- due to demand surge, covid excuse, etc. Contact them to to verify.

Lee Precision, Inc.. Custom Services

Custom service ordering area. Order custom bullet molds, custom case length gauges and custom die sets.

leeprecision.com

Thank you for the information!

 

[SkullKeeper]

Think I’ve located one

 

[norfolk shooter]

You chaps are lucky you have Lee. In the UK we can only get the standard stuff no custom dies for us

 

[Shootist43]

Skullkeeper, the 416 Rigby is about the only caliber I don't have a Taper Crimp Die for. My 416 Rigby is a single shot i.e. a Ruger No.1. You might try asking to borrow one from an AH member with you paying the postage both ways. I've used Lee's "Custom Shop" to make several different crimping dies for me. Service was top drawer.

 

[Ryan]

I found it at FS Reloading, where I got my 375 crimp. Don't know if that is standard press threads or not but my 375 Ruger one fits my RCBS press just fine.

 

[neckdeep]

Its not standard threads, I had one a while back and was much larger than standard forster rings to put in my forster press, if you have a different press may work for that

 

[Shootist43]

Skullkeeper lots of single stage presses come with a bushing that reduces the 1 & 1/4" threaded hole down to 7/8". All you have to do is remove the bushing and insert the Crimping Die.

 

[Ryan]

Skullkeeper lots of single stage presses come with a bushing that reduces the 1 & 1/4" threaded hole down to 7/8". All you have to do is remove the bushing and insert the Crimping Die.

Yep, I just pulled that bushing out of my RCBS press and measured, it is 1 1/4". Things I'll remember if this comes up again.

 

[SkullKeeper]

Skullkeeper, the 416 Rigby is about the only caliber I don't have a Taper Crimp Die for. My 416 Rigby is a single shot i.e. a Ruger No.1. You might try asking to borrow one from an AH member with you paying the postage both ways. I've used Lee's "Custom Shop" to make several different crimping dies for me. Service was top drawer.

Thank you buddy!

 

[SkullKeeper]

Its not standard threads, I had one a while back and was much larger than standard forster rings to put in my forster press, if you have a different press may work for that

Yes I’ve got a Lee classic - it will work fine