Are they a direct fit or require enlargement of the slot in the tang?
World's most popular community & resource for hunting in Africa since 2007
Custom Safeties For Ruger #1
- Thread starter CJNJ
- Start date
DocHolliday
AH senior member
- Joined
- Sep 12, 2024
- Messages
- 51
- Reaction score
- 91
- Location
- Louisiana
- Member of
- Life DSC, Benefactor Life NRA, Silver Life Sponsor NWTF
- Hunted
- Lower 48, Argentina, Canada, Africa
Direct fit
CJNJ
AH veteran
- Joined
- Apr 27, 2025
- Messages
- 110
- Reaction score
- 204
- Location
- west coast nj
- Member of
- Life Member NRA
- Hunted
- Pennsylvania, New Jersey USA
Was advised today by my gunsmith of 5 week backlog so it will be a while before I can post a photo of the custom safety I mentioned at the top of this thread.
Rafiki
AH fanatic
- Joined
- Mar 19, 2023
- Messages
- 705
- Reaction score
- 1,557
- Location
- Florida and Minnesota
- Media
- 8
- Hunted
- Tanzania
5 weeks to do what? Just to install an after market safety?
CJNJ
AH veteran
- Joined
- Apr 27, 2025
- Messages
- 110
- Reaction score
- 204
- Location
- west coast nj
- Member of
- Life Member NRA
- Hunted
- Pennsylvania, New Jersey USA
That and a Jard trigger. Had I known I would have done it myself. I’m sure I could overcome any difficulties in 5-6 weeks!
Doug3006
AH legend
- Joined
- Nov 18, 2015
- Messages
- 2,693
- Reaction score
- 10,683
- Media
- 19
- Member of
- SCI, NRA
- Hunted
- Namibia (X3), Zambia, Zimbabwe, South Africa
My gunsmith routinely has a 6-8 week backlog. If you think that’s bad, try making a non-emergency dental appointment. They’ll see you in the Fall!
The trop is pretty good, I suspect Krick is probably making them for Trop. The trop was designed so that the rim on Nitro sized calibers didn't get stuck on ejection, dangerously slowing reloads.
Custom #1s typically do it a better way. I quick trip through the mill makes a recess where the safety operates, then a safety is milled to operate inside that trough. The #1 custom safety should be shaped like a shark fin so it allows ejected brass to clear it or launch off of it away from the chamber. The back side of the safety should be textured so your thumb can operate it easily.
The factory safety is investment cast trash that rattles around and is pretty crude. About as much as one can expect from a $2000ish mass produced rifle of good quality.
Show a competent gunsmith a photo of a Dakota Model 10 safety and ask them to make you something like that on your Ruger #1 and you'll be very pleased. Not a crazy hard job.
Members online
- ClarkC
- Beck
- RobBrown505
- Moosemind
- RR 314
- Spartan5
- Rimbaud
- Schüler Jumbo
- Flanders357
- Kynoch2015
- jbirdwell
- Aaron.F
- jduckhunter
- Hannay
- John Wasmuth
- Rubi_300
- cwpayton
- mdwest
- JTT
- Woodcarver
- Ser Rodrik
- KCSafari
- Mark Biggerstaff
- bakerb
- Mizzou100
- meigsbucks
- wvfred
- D.L.W.
- coreydb
- Monstermuley24
- Lopehunter
- Flbt
- SCmackey
- MRBlack
- slam8031
- Datchew
- scuba14c
- CRCO
- Brickman301
- Will22
- Racer00
- Ryan Brown
- Elkeater
- R eight
- tmjames0709
- WAB
- Ontario Hunter
- Moody808
- James Cook
- The35Whelen
Forum statistics
Latest profile posts
Mauser3000 wrote on HBartley's profile.
Hello,
I saw your post selling left hand rifles. Do you have any additional pics of the .416 Rem mag?
Thank you.
-Nathan
I saw your post selling left hand rifles. Do you have any additional pics of the .416 Rem mag?
Thank you.
-Nathan
Mauser3000 wrote on gbflyer's profile.
Hello, I saw your post selling left hand rifles. Do you have any other left hand rifles you may let go of? Also can you send a few additional pics of Borden rifle?
Thank you.
-Nathan
Thank you.
-Nathan
DaBill wrote on Fzj80's profile.
Just FYI $499 on https://www.eurooptic.com/leupold-v...3KHXPC4WuxtO6snqpCTN-T7_VZhmxHnXsaL24d3SNArHh
Better Luck if you lower your price
Better Luck if you lower your price
