Tight Bolt & Line On Casing

[Grumpy gumpy]

Good idea. Will try. I’m thinking but as well.

Do not use steel wool, if it’s a burr it will tear off and go everywhere and not achieve much . A small round file or similar to remove the burr, clean with solvent and then wipe with suitable oil
Gumpy

 

[Grumpy gumpy]

Fixed! Shoutout to @Ontario Hunter for the idea.

Too late. You will need to flush it clean and blow out the fine wire bits.
Gumpy

 

[csmcclain]

Too late. You will need to flush it clean and blow out the fine wire bits.
Gumpy

Yes. Cleaning it good after doing this. I just used a standard wire brush on the chamber where it was getting stuck (no steel wool).

Good idea. Will try. I’m thinking but as well.

also, just realized I never finished this sentence, but now I have no clue what I was thinking about doing. I guess that’s the issue with being stupid.

 

[Grumpy gumpy]

Yes. Cleaning it good after doing this. I just used a standard wire brush on the chamber where it was getting stuck (no steel wool).

also, just realized I never finished this sentence, but now I have no clue what I was thinking about doing. I guess that’s the issue with being stupid.

Not stupid, just easily distrac……oh look , bunny…..



Gumpy

 

[fourfive8]

You say “fixed”. Hmm…. OK…. I still can’t follow what the issue was. Unclear why some snap cap dummy or ammo fit into chamber and some snap cap dummy’s didn’t. Makes no sense. To think that steel wool will remove a steel burr in the chamber seems a stretch to me. Barrel steel is tough and hard- much harder than steel wool, which is soft steel. It might remove a particle of something stuck on the chamber wall but actually abrade away a steel burr..?

A simple way to actually view the chamber of any firearm without having a bore scope is to use a simple thin mirror and bore light. I had some broken mirror pieces in the shop? Picked out a piece a couple inches long and about the width of a popsicle stick and epoxied it to a popsicle stick.

Put gun in cradle. Put bore light in muzzle. Hold mirror next to rear of chamber at angle so you can look into chamber along bore axis. Amazing how simple and how well this works for viewing a chamber.

 

[csmcclain]

You say “fixed”. Hmm…. OK…. I still can’t follow what the issue was. Unclear why some snap cap dummy or ammo fit into chamber and some snap cap dummy’s didn’t. Makes no sense. To think that steel wool will remove a steel burr in the chamber seems a stretch to me. Barrel steel is tough and hard- much harder than steel wool, which is soft steel. It might remove a particle of something stuck on the chamber wall but actually abrade away a steel burr..?

A simple way to actually view the chamber of any firearm without having a bore scope is to use a simple thin mirror and bore light. I had some broken mirror pieces in the shop? Picked out a piece a couple inches long and about the width of a popsicle stick and epoxied it to a popsicle stick.

Put gun in cradle. Put bore light in muzzle. Hold mirror next to rear of chamber at angle so you can look into chamber along bore axis. Amazing how simple and how well this works for viewing a chamber.

View attachment 801127

I genuinely cannot figure it out, but it cycles much better now. I have a borescope coming in the mail that I will check it with this week. If any additional filing is needed, I will take care of that then.

 

[Grumpy gumpy]

You say “fixed”. Hmm…. OK…. I still can’t follow what the issue was. Unclear why some snap cap dummy or ammo fit into chamber and some snap cap dummy’s didn’t. Makes no sense. To think that steel wool will remove a steel burr in the chamber seems a stretch to me. Barrel steel is tough and hard- much harder than steel wool, which is soft steel. It might remove a particle of something stuck on the chamber wall but actually abrade away a steel burr..?

A simple way to actually view the chamber of any firearm without having a bore scope is to use a simple thin mirror and bore light. I had some broken mirror pieces in the shop? Picked out a piece a couple inches long and about the width of a popsicle stick and epoxied it to a popsicle stick.

Put gun in cradle. Put bore light in muzzle. Hold mirror next to rear of chamber at angle so you can look into chamber along bore axis. Amazing how simple and how well this works for viewing a chamber.

View attachment 801127

Similar principle to the armourers barrel inspection tool but with more sharp edges
Gumpy