SAFETY WARNING!

But the "legal matters" are important. These are indeed ghastly photos and emotional testimonies. But one has to ask how is that Blaser is still in business if the weapon has a legitimate design flaw producing these sorts of injuries? One successful suite would likely crush Blaser. Where is that plaintiff who has proven product liability? If the design of this rifle rather than an obstruction or overload hurt anyone, I wish them every success in court. Facts, not forum posts, will matter in that venue. Until then, my own experience with Blaser ,and that of a fairly broad range of colleagues, is universally positive.
The R93 has had some internet noise. I do know that Blaser has yet to be sued successfully for any product failure. Whether or not their has ever been a settlement, I have no way of knowing. I personally believe the R8 is the finest production rifle on the market. I own one in three calibers and have used it on everything from buff to duiker.
The firearm DEVA testing agency is a manufacturer's association co-owned by major German brands like Blaser, Heckler & Koch, Heym, Mauser, Merkel, Sauer, etc.

"Conflict of interest ", anybody?
To me, Blaser co-owning DEVA would be like Boeing co-owning the NTSB.
Or Goldman-Sachs co-owning Moody's Ratings.


I would expect that any plaintiff suing Blaser for his R93's catastrophic failure would have a very steep uphill battle. Take the case of one owner shooting factory Norma .30-06 ammo:
In July 2014, 69-year-old Christer Svensson experienced an accident where his R93 chambered for .30-06 Springfield exploded while loading his rifle on a shooting range near Bollnäs in Sweden, resulting in the bolt hitting his face. Svensson was using Norma factory ammunition. He turned in the rifle to Blaser, but wanted the Swedish National Forensic Centre to investigate the matter. However, he later agreed to the wish of Blaser and its Swedish distributors that all technical investigation would be performed by the German DEVA institute. The DEVA report concluded that the damages to the firearm almost certainly came from a combination of an overpressure and a problem with the casing of the cartridge. Svensson told the Swedish hunting and firearms magazine Svensk Jakt that he had difficulties getting his firearm back from the testing, and that it had been modified when he finally received it. He stated that the chamber and bolt head had been chopped off, and that the barrel did not have a stamped serial number anymore, and claimed the serial number appeared to have been reapplied by hand. He also claimed his rifle originally had a front sight mounted to it which was missing on the returned barrel.

Blaser bolts, R8 vs R93.png



The main reinforcement of R8 compared to R93 is a conical part which is driven inside the collet and pushed it out on bolt close forcing the expansion from inside. It ensures that the collet has expanded at the most forward position of the bolt. If that conical piece is not retracted back by moving the bolt handle the collet physically cannot open. R93 didn't have that, when R93 collet was expanded there was an empty space inside it, so theoretically it could collapse.


Talk without proof...... is just talk.....
AOC and Blaser R93, some gun2.jpeg


Well, then, here's your meme.













I'd wager that the R93 bolt could have been redesigned with an R8-style internal sleeve to lock the collets in battery, and Blaser could have then recalled the old bolts. That'd have been the honorable solution. But, a recall would have implied design fault, and thus personal injury liability. Instead, Blaser left R93 owners stuck with an inferior model that can (apparently, if the ammo isn't just perfect) fail the user, and abandoned the R93 for the R8 (which won't accept R93 barrels).

Before I read this thread, I'd decided a few days ago that I wasn't going to buy a used Blaser R93.
(To all R93 owners keeping theirs, I strongly urge that you use only retail purchased factory ammo and keep the receipts. No handloads! And wear the best eye/face protection available.)

Furthermore, today I've decided not to buy anything from Blaser at all, even though I currently believe the R8 action is strong and safe. I became suspicious about Blaser's ethics regarding the 2014 Christer Svensson KB, but now I simply don't trust the company.

My thanks to the OP @PaulT, @Kano, @Norwegianwoods, and others who didn't duck this important safety issue. Respect!
 
The firearm DEVA testing agency is a manufacturer's association co-owned by major German brands like Blaser, Heckler & Koch, Heym, Mauser, Merkel, Sauer, etc.

"Conflict of interest ", anybody?
To me, Blaser co-owning DEVA would be like Boeing co-owning the NTSB.
Or Goldman-Sachs co-owning Moody's Ratings.


I would expect that any plaintiff suing Blaser for his R93's catastrophic failure would have a very steep uphill battle. Take the case of one owner shooting factory Norma .30-06 ammo:


View attachment 808905






View attachment 808904

Well, then, here's your meme.













I'd wager that the R93 bolt could have been redesigned with an R8-style internal sleeve to lock the collets in battery, and Blaser could have then recalled the old bolts. That'd have been the honorable solution. But, a recall would have implied design fault, and thus personal injury liability. Instead, Blaser left R93 owners stuck with an inferior model that can (apparently, if the ammo isn't just perfect) fail the user, and abandoned the R93 for the R8 (which won't accept R93 barrels).

Before I read this thread, I'd decided a few days ago that I wasn't going to buy a used Blaser R93.
(To all R93 owners keeping theirs, I strongly urge that you use only retail purchased factory ammo and keep the receipts. No handloads! And wear the best eye/face protection available.)

Furthermore, today I've decided not to buy anything from Blaser at all, even though I currently believe the R8 action is strong and safe. I became suspicious about Blaser's ethics regarding the 2014 Christer Svensson KB, but now I simply don't trust the company.

My thanks to the OP @PaulT, @Kano, @Norwegianwoods, and others who didn't duck this important safety issue. Respect!
That is really more your loss, not theirs.

I do not know what actually happened with respect to those accidents. Neither do you. I simply pointed out that the company has not been proven to be negligent, and has not issued a recall. They have indeed improved the design with the R8. That seems like logical product development/improvement to me.

If you feel more virtuous boycotting their products, then certainly do so. Post memes - though maybe actually firing a few rounds from one would enhance the legitimacy of your criticism. I have had nothing but very positive interactions with Blaser and own a number of their products which I have been using for well over a decade. I remain convinced it is the finest production rifle for a traveling hunter ever created. In synthetic form, it is, at least in my fairly experience, it is also the most environment proof rifle I have used.
 
That is really more your loss, not theirs.
Actually, I've just saved myself $$$$. Will instead buy a Mauser/M70 for my .300 Mag.
The game won't discern any difference, and neither will I.

I do not know what actually happened with respect to those accidents. Neither do you. I simply pointed out that the company has not been proven to be negligent,
Blaser is a co-owner of the very agency which tests blown-up R93s. Mm, hmmmm.
That doesn't concern you?
"Who will guard the guardians? " ~ Juvenal

and has not issued a recall.
IMO, they could have, and should have. I suspect that the cost of designing a safer bolt and recalling the original one at their expense was so prohibitive that they opted instead to roll out the R8 for sale. (The parallels of this with that unnamed German airplane factory I mentioned are just eerie.)

They have indeed improved the design with the R8. That seems like logical product development/improvement to me.
The R93 collets were internally unsupported, and their shallower angle probably didn't help with lock-up.
Abysmal safety engineering. Wasn't the R8 bolt within their ken from the start?

If you feel more virtuous boycotting their products, then certainly do so. Post memes - though maybe actually firing a few rounds from one would enhance the legitimacy of your criticism.
Please re-read my post with better comprehension. I did not criticize the R8, but there's no point in firing one as I will not patronize Blaser despite how much I may have liked the R8. I've dealt plenty with German companies in different industries, and I've often found them particularly avoidant in accepting personal responsibility for design flaws. However, they certainly love to boast about their Teutonic engineering. I'd hoped Blaser was an exception.

Moral: Mess up, fess up.

Thank you for you reply, but it had a whiff of cultism.
 
From a cursory search, the timetable is illuminating:

1993 R93 introduced
1994 R93 Koblenz Germany failure
2003 R93 8x68S failure, Norwegian Jan Sørlie
2004 R93 .300 Wby failure, Albrecht Huf, Koblenz Germany
2008 R8 introduced (to date, ~300,000 sold)
2009 R93 7mm Rem Mag failure, Spaniard Jesus Nieto
2014 R93 .338 Lapua Mag failure, Australian Thexton Daikin, Blaser lost in court
2014 R93 .30-06 failure, Swede Christer Svensson
2014 R93 failure, Swede Tony Kristoffersson
2016 R93 discontinued (200,000+ sold)

A year after introduction, the first R93 failure, followed by at least two more the next decade.

I'm fascinated to learn how on Earth Blaser managed to upsell the R8 without market curiosity why it was worth buying over the R93. It wasn't just the removable mag, as some R8s have fixed mags. I mean, really, what did the early R8 advertising focus on? Increased strength seems illogical as the R93 was already stronger than the M98.

How did they concurrently sell both models for 8 years?
Why didn't the market wonder "Hmmm, well what's wrong with my R93? "
 
Actually, I've just saved myself $$$$. Will instead buy a Mauser/M70 for my .300 Mag.
The game won't discern any difference, and neither will I.


Blaser is a co-owner of the very agency which tests blown-up R93s. Mm, hmmmm.
That doesn't concern you?
"Who will guard the guardians? " ~ Juvenal


IMO, they could have, and should have. I suspect that the cost of designing a safer bolt and recalling the original one at their expense was so prohibitive that they opted instead to roll out the R8 for sale. (The parallels of this with that unnamed German airplane factory I mentioned are just eerie.)


The R93 collets were internally unsupported, and their shallower angle probably didn't help with lock-up.
Abysmal safety engineering. Wasn't the R8 bolt within their ken from the start?


Please re-read my post with better comprehension. I did not criticize the R8, but there's no point in firing one as I will not patronize Blaser despite how much I may have liked the R8. I've dealt plenty with German companies in different industries, and I've often found them particularly avoidant in accepting personal responsibility for design flaws. However, they certainly love to boast about their Teutonic engineering. I'd hoped Blaser was an exception.

Moral: Mess up, fess up.

Thank you for you reply, but it had a whiff of cultism.
Whiff of cultism? You should see my gun room. No, just a solid snort full of virtue signaling. You are just another critic with zero experience with a Blaser, but cloaking it in moral judgmentalism. But, I fully acknowledge that is your absolute right to do so.
 
From a cursory search, the timetable is illuminating:

1993 R93 introduced
1994 R93 Koblenz Germany failure
2003 R93 8x68S failure, Norwegian Jan Sørlie
2004 R93 .300 Wby failure, Albrecht Huf, Koblenz Germany
2008 R8 introduced (to date, ~300,000 sold)
2009 R93 7mm Rem Mag failure, Spaniard Jesus Nieto
2014 R93 .338 Lapua Mag failure, Australian Thexton Daikin, Blaser lost in court
2014 R93 .30-06 failure, Swede Christer Svensson
2014 R93 failure, Swede Tony Kristoffersson
2016 R93 discontinued (200,000+ sold)

A year after introduction, the first R93 failure, followed by at least two more the next decade.

I'm fascinated to learn how on Earth Blaser managed to upsell the R8 without market curiosity why it was worth buying over the R93. It wasn't just the removable mag, as some R8s have fixed mags. I mean, really, what did the early R8 advertising focus on? Increased strength seems illogical as the R93 was already stronger than the M98.

How did they concurrently sell both models for 8 years?
Why didn't the market wonder "Hmmm, well what's wrong with my R93? "
Do you happen to have any information on similar accidents happening with the R8 version?
I do own several R8s and I would appreciate any well-verified information that you might have and be willing to share.
Tks.
 
"How did they concurrently sell both models for 8 years?
Why didn't the market wonder "Hmmm, well what's wrong with my R93? ""

Bloody good question. I, however wonder if people thought of it like say Ruger having the M77 and Ruger American, or Remm with the 700 and 788, that is, just another model.
 
Do you happen to have any information on similar accidents happening with the R8 version?
I was researching this few years ago, and I was the one to post an investigation report on R93, on this thread here. What prompted my research was - there are hundreds of various rifle models in the world, and R93 bolt failures kept popping up, more often then any other rifle model

I could not find any failure report on R8 then.

However, every rifle may be prone to failure, with faulty ammo, exessive pressures etc, not even mauser is immune to that.

So, I dont think it did not happen with R8 on such reasons.
But I did not find any such report.

Well,, not all failures are reported on internet.
I think Blaser kept a good job, of keeping it quiet for R93. Most likely they will keep quiet with R8 too for any sporadic case.

I hunted few times with rental R8, and I find them very nice, handy, with good ergonomics, and very accurate.
 
Last edited:
Whiff of cultism? You should see my gun room. No, just a solid snort full of virtue signaling. You are just another critic with zero experience with a Blaser, but cloaking it in moral judgmentalism.
Ah, for the second time you mention my irrelevant inexperience with a Blaser (R8), even when I called you on that very point. The R8 seems a safer action than the R93. I know of no R8 catastrophic failures. I don't have an issue with the R8, but with the R93 and the company. How are you confused about that?

Not that it really counts, or matters, but my Blaser experience isn't "zero". I was very fortunate to have survived firing a few rounds from a .416 Rem Mag R93 years ago at NRA Whittington with the owner's handloads. Yikes.

Again, you have no qualms about the German gun companies owning their own testing agency DEVA which officiates on the probable cause of R93 KBs? "Pfizer owning the FDA" is OK with you?

Yes, I am indeed morally judgmental about Blaser. Somebody has to counterbalance the cultists.

Do you happen to have any information on similar accidents happening with the R8 version?
I do own several R8s and I would appreciate any well-verified information that you might have and be willing to share.
Tks.
I've read or heard of no such reports with the R8, a much improved system.
They should have introduced that model, vs. the clearly flawed R93.
I wouldn't worry about your R8. Good hunting!

"How did they concurrently sell both models for 8 years?
Why didn't the market wonder "Hmmm, well what's wrong with my R93? ""

Bloody good question. I, however wonder if people thought of it like say Ruger having the M77 and Ruger American, or Remm with the 700 and 788, that is, just another model.
Probably something like that. I'm going to look into it; am very curious.
Might make an interesting business case study model.
(Ford could have learned from upgrade misdirection when their Pinto model kept exploding.)

Ilhan Omar and Blaser R93.jpeg

On a separate note, I need to apologize for a goof I made.

Confusing my dusky Democratic Socialist Congresswomen, it shouldn't have been AOC in my meme but Ilhan Omar. It was she who infamously described 9/11 as merely "Some people did something."

Corrected.
 
Last edited:
Most R93 KBs allegedly are related to/caused by overcharged handloads, with one barrel obstruction.
I can generally stipulate that, but there are two cases of factory rounds by the shooters' insistence (Australian Thexton Daikin and Swede Christer Svensson).

The other issue is that whatever the cause, the R93 failure mode is catastrophic, and severely injurious.
This is seldom true of a Mauser 98 or Winchester M70.

Below right is Christer Svensson's destroyed .30-06 R93 bolt, collets, and shattered bolt head.

Blaser R93 bolt head, and after KB.png


The .30-06's maximum average pressure limit is CIP 4,050 bar (58,740 psi) or SAAMI piezoelectric 60,000 psi.

The R93 lockup was tested by DEVA up to 8,000 bar (116,000 psi), which is not a per-rifle standard (as Blaser seems to like us to infer), just what that particular test rifle withstood.

Unless a .30-06 case is stuffed with Bulleye, there's no way that a factory Norma round so grossly exceeded 60,000 psi.

I'm wondering if a weak case let go, and the escaping gas velocity and direction failed the R93 design. The collet fingers ("tongues" in the patent description) are not (as in the R8) splayed out by an internal sleeve and thus locked in the barrel's annular channel, rather, the R93 fingers are cammed outwards by the bolt head rear cone and held there with bolt face thrust during ignition.

Now, to my layman's theory.

If the brass case head fails, the gas could escape the bolt head enclosure via the extractor cutout, thus pressurizing the frontal face of the collet fingers. (In an M98 turnbolt, escaping gas pressure cannot turn the lugs out of the raceway.)

Blaser-R93-drawing - gas escaping.jpg


This gas pressure on the fingers overcomes the bolt head rear thrust's shear force (which wasn't 100% due to the brass case blowout) between the fingers and the annular barrel channel, and pushes the fingers down the head's rear cone. There is nothing (as with the R8 bolt sleeve) to mechanically prevent the fingers from dropping out of the barrel channel. Such reduces the bearing contact area, and begins to compromise the strength of lockup.

The diagram below demonstrates if the escaping gas pushes the collet finger to the shear line (circled in blue). At that point, the collapsing fingers act like a sear releasing its trigger. Bolt head lockup = zero and the bolt body is suddenly free to jet rearward from tremendous pressure.
Blaser R93 bolt in operation - half lockup,2.png

Examine again Christer Svensson's R93's collet fingers (compared to their original shape). Their front edges have been brutally pried up and deformed from the gas pressure.

Blaser R93 bolt head, and after KB.png



The below two R93 bolt KBs below (from other incidents) were so energetic that they broke off several fingers and bent the remaining fingers beyond material yield strength (hence their permanent splayed out deformity).

Blaser10_zps5cbf5485.jpg


As I've stressed, underneath the R93 collet fingers is nothing to seize them up in place (as with the R8 sleeve).

Sorry Blaser Fans, but the R93 breech never was a great system. Your R93s c/should have been the R8 style since 1993, as the expanding madrel was well known back then. From what I understand about the R8 breech locking system, it has my respect.

____
The Blaser R93's occasional KBs have been commented on in other forums, with about the same ratio of fans vs. detractors. For example:


____
I read in another forum that the supposed reason for the R8 rollout was the imminent expiration of the R93 patent.

From AI:
The R93’s core German breech/locking patent—DE4305700C1, filed on February 25, 1993—expired in February 2013. Its patent record lists February 26, 2013 as the expiry date.

That’s the date for this particular patent, not necessarily every R93-related patent worldwide: separate patents for later features or improvements had their own terms and expiry dates.
The R8 was introduced five years before the R93 patent expired. Interesting....

____
Giving Blaser the company a hard pass (despite its well regarded and impressive R8), I'm now looking at the straight-pull Merkel Helix.

I've found no reports of catastrophic failure or injuries in the Helix.

I hope this post has been helpful.
 

Attachments

  • Blaser-R93-drawing_zps5714900f.jpg
    Blaser-R93-drawing_zps5714900f.jpg
    49.9 KB · Views: 0
Last edited:

Forum statistics

Threads
71,134
Messages
1,594,814
Members
175,465
Latest member
DonDaniels
 

 

 

Latest posts

Latest profile posts

Mattias Stedt wrote on Bushcat Safaris's profile.
A good safari brings a great experience that fulfils your expectations, but a great safari also brings professionalism and friendship. Bushcat Safaris fills all those boxes and we have a lot of great memories from the bush with rifle in hand.
My warmest recommendation for you to plan a safari with these guys and be ready for a great time. As they say, we are not here for a long time, we’re here for a great time!
Looking back at a great year
cb3a8f6b-e471-4478-8e24-fa9422db8d4d.jpeg
IMG_7851.jpeg
20bdfb9b-dfe7-46e1-9d90-981da068d8fc.jpeg
915d3c84-4177-457f-a11d-0771a765f4c3.jpeg
52bf1f94-ccae-4160-bc7a-ae8d7969278b.jpeg
8d4d83fd-64e0-466c-90bc-868a7492cf61.jpeg
a31db0e9-e914-41e0-a1c2-785617ad41ac.jpeg
A small glimpse into a fantastic season
e81d375e-faf8-4cbe-bf9c-afe325b97bbb.jpeg
9a766ff2-0919-4a4a-b09c-ede9ce09b94e.jpeg
22ecca2a-8c07-4eab-becb-2ee49dca9fc3.jpeg
IMG_7820.jpeg
fa806fce-29ef-485b-9544-b103140a7ad1.jpeg
b4e3df48-40f2-4593-95bb-efbe5fdeed09.jpeg
A0A409A3-B41C-41DF-91B3-FEBFC48FF566.jpeg
f53b657c-2414-450f-bf44-292f3bd3e46c.jpeg
Don't forget to Check out our Mountain package. Chase that Vaali find the elusive Grey Ghost and spot a Mountain Reedbuck. in Gods Country. find refuge in the field and freedom under wide open skies.
 
Top