My tally qd base on the front of my mod 70 has the back screw just spinning and not solid. Surely this isn't stripped but I have no other idea. Thoughts? The front screw on that base is tight and good.
World's most popular community & resource for hunting in Africa since 2007
I may have an issue - tally bases
- Thread starter Hornedfrogbbq
- Start date
Grumpy gumpy
AH elite
Only way to be sure is take it off and check
Gumpy
Quick edit, I mean take the screw off/out and check
Effing stripped. There aren't longer screws that work on a regular tapped mod 70 is there?
I hate to say it but I have 6 different sets of Talley QD rings. 4 of them the screws have stripped out. I have emailed twice for replacement which they have sent for no cost. But I’m looking to move on to another brand. Not acceptable IMO.
Ray B
AH ambassador
First- remove the screw that won't tighten and look at the threads. If it is stripped what's left of the threads will be flat and shiny. If the threads are intact it may be that the screws are mixed. The screws for the front base are shorter than the ones for the bridge. A screw from the front isn't long enough to reach the threads in the bridge.
Grumpy gumpy
AH elite
Can it be fixed with a longer screw as suggested or cut to the next thread size up?
Gumpy
- Joined
- Mar 17, 2023
- Messages
- 1,447
- Reaction score
- 3,387
- Location
- Dry ass side of Texas
- Media
- 16
- Member of
- Puro pinche low fence hunting, Anglo SCI
- Hunted
- Mexico, Canada,USA, Spain, Morocco, Zimbabwe
I’m have had a couple strip out myself
But I’m to cheap to start over with a new brand
MTJumbo
AH member
- Joined
- May 13, 2026
- Messages
- 39
- Reaction score
- 60
- Location
- Missoula, MT
- Member of
- NRA Patron Life Member, RMEF, Montana Weapons Collectors Society, Western MT Fish & Game Assoc, SCI
- Hunted
- Montana, New Mexico, CO, WA, ID, KS, MO, OK, Canada
IMO, either the threads on the tapped screw hold in the receiver are stripped or the screw is too short to engage the receiver threads or the screw threads are stripped. You could try to run the appropriate size tap into the receiver and retry a fresh screw. Or a longer screw. When I was repairing facial fracture, if a screw 1.5 mm screw failed to hold, the set had emergency screws of 1.8 mm or 2mm or some slightly larger diameter to grab the bone in an over-sized hole. Bone holes are of a specific mm size without tapped threads. The drill size might be 1.1 mm size. Large bone sometimes is tapped but these small screws are for non-tapped holes. Tell me how your project is going. There might be an easy fix for it. I hope you are not screwed. Lol.
Get a 6/48 bottoming tap to clean up the threads in the receiver. Be very careful not get the tap in a bind and break it off in the receiver. Lube is your friend. Then screw a new 6/48 screw into the hole to make sure the threads are good. Go easy. Do not tighten it at all. You are just checking the threads. If all that is good re-install the base with the correct length screws. Check with Tally. Use a tiny, tiny bit off blue or purple Loctite or install them dry. Whatever is your preferred method.
Good luck. Just go slow and easy.
Good luck. Just go slow and easy.
Amazon.com: Hanson Carbon Steel Bottom Tap 6-48 Thread : Industrial & Scientific
Buy Hanson Carbon Steel Bottom Tap 6-48 Thread: Hand Threading Taps - Amazon.com ✓ FREE DELIVERY possible on eligible purchases
a.co
Well Tally is shipping me two new screws. No charge. Great communication online.
The threads are stripped on the screw. I completely did it myself. They do not prefer blue loctite because you need to reduce the torque by 25%ish when using it. They just prefer dry and 25lbs on the Wheeler.
Great customer service!
The threads are stripped on the screw. I completely did it myself. They do not prefer blue loctite because you need to reduce the torque by 25%ish when using it. They just prefer dry and 25lbs on the Wheeler.
Great customer service!
MTJumbo
AH member
- Joined
- May 13, 2026
- Messages
- 39
- Reaction score
- 60
- Location
- Missoula, MT
- Member of
- NRA Patron Life Member, RMEF, Montana Weapons Collectors Society, Western MT Fish & Game Assoc, SCI
- Hunted
- Montana, New Mexico, CO, WA, ID, KS, MO, OK, Canada
Thanks RSL. I wasn't sure if a 6-48 tap would be the correct size. A broken tap remover is available from Brownells. Just in case a tap is broken off while chasing the threads. I hope it doesn't happen.
Yes, clean the receiver threads with a bottoming tap. I use a blast of WD40 in threaded hole to blow out any crap the tap leaves behind. WD40 because it's harmless to everything. Then you should remove the WD40 with alcohol or acetone, on a q-tip, so you have a clean dry hole for your new screw.
;-)
;-)
220, 221...whatever it takes.
By the by, Talley sent me a package or replacement screws absolutely free. They worked perfectly. Huge fan of their customer service.
Cucuy
AH veteran
- Joined
- Jul 26, 2015
- Messages
- 174
- Reaction score
- 390
- Member of
- NRA, DSC, SCI
- Hunted
- Namibia, USA, Canada
Mizzou100
AH veteran
- Joined
- Dec 7, 2025
- Messages
- 101
- Reaction score
- 180
I have the same exact issue on a new model 70 i installed talley bases on, was only toquing to 20lbs, feels stripped.
Pull the screw out and see if the end is "shiny" versus having threads. If so, give them a call or email. They are tremendously helpful.
Members online
- AustinM
- etsonaut
- BigGame
- cdub
- Beerhunter
- Ku-winda
- Fatback
- Schüler Jumbo
- Atticus
- JD Noblin
- Hogpatrol
- meigsbucks
- Tdsmith517
- HunterDoc
- MRBlack
- Racer00
- WISafariHunter
- gearguywb
- Justbryan
- Mark458
- Hunt anything
- autofire
- Pheroze
- Saysaw0509
- caanaya5711
- kpoynter
- Spartan5
- 458JCE
- WAB
- Rubberhead
- Shako Badhan
- Todd Fall
- codofish
- Betterinthebush
- Albert GRANT
- LeftySixgun
- HuntingGold
- Cucuy
- Ridge Runner
- Tubby’s Canteen
- wheeler
- Rem280
- mms45
- 375 Ruger Fan
- Tanks
- HunterRick56
- Aaron N
- small bore
- jb0902
- Jondnov
Forum statistics
Latest profile posts
K_P wrote on Buckleyguy12's profile.
Good morning from Montana.
I'm looking at a post from 2018 where you were looking for a lefty Winchester in .375 H&H Magnum. I'm selling mine. My email is kdp59935@gmail.com in the event that you're still searching for a unicorn.
Best,
Kelly Palmer
I'm looking at a post from 2018 where you were looking for a lefty Winchester in .375 H&H Magnum. I'm selling mine. My email is kdp59935@gmail.com in the event that you're still searching for a unicorn.
Best,
Kelly Palmer
Gents, if you book and pay your deposit before the end of this year , you can have the bigger cull package for the 2026 price! https://www.africahunting.com/threa...griffiths-safaris-starting-at-us-2-560.96285/
I am currently in Northern Cape scouting a hunting area, we will have lots of amazing hunting opportunities for 2027! I will post updated available dates soon!
Azklmsr wrote on MANKAZANA SAFARIS's profile.
Good Evening. I am very interested in you hunt for the spiral slam. March in 2028 would be fine for me
Couple of quick questions:
1) Can we add some additional species on
2) what do you want for a deposit?
3) how do you want me to sign up
I'm on whats app or email
Kurt [redacted]
have a great evening
Couple of quick questions:
1) Can we add some additional species on
2) what do you want for a deposit?
3) how do you want me to sign up
I'm on whats app or email
Kurt [redacted]
have a great evening