Search results

PowderValley(dot)com has Federal and CCI Large Rifle MAGNUM primers In-Stock again.

PowderValley(dot)com has BOTH - Federal 215 and CCI 250 Large Rifle MAGNUM primers In-Stock!

PM sent

Not saying this is the situation here, especially if you are uniforming the primer pocket after full length sizing... Sometimes people get the expander stem too deep and the expander ball can press slightly against the bottom of the case. When that happens it can put a bulge in the primer...

Yes, but coming up that far must be done in steps. Neck up to 0.338, anneal, neck up to 0.375, anneal, then full size for 404. If you try to do it in one shot you'll split a lot of case necks. Even 1 intermediate spot like going up to 0.375 and then 0.423 and you'll get very inconsistent neck...

ADG makes 375RUM and is readily available. I've found it as cheap as $117/50 in a hard case that can be used with loaded rounds.

Case head size is not significantly different. I shoot it in a CRF bolt and a single shot. Still picks up the rim and ejects it properly.

I made a post on the reloading forum about making 404J brass out of (375) Remington Ultra Mag brass. The 404J case was the parent case when the RUM line was designed. It's extremely easy to make...until we get a reliable source for proper 404J headstamp brass again.

While not your target 450gr, North Fork 430gr at 2345fps will get your attention. With the relief grooves in the solid shank, North Fork bullets keep pressures down compared to traditional bullets of equal weight. These are an "improved" TB Bear Claw on my opinion. Extremely high weight...

Range Results (100yds)

Had some virgin RP brass to experiment with. I did lose 3 cases out of 26 due to miscalculations on my part.

Fired Rounds

Loaded rounds

In these trying times where brass has become scarce. I want to keep my 404Jeffery headstamped brass for Africa. So I wanted to make my own. While there is a thread on these forums about forming 404J from 375H&H; the smarter choice is forming from cases that use 404J as the parent case. I'm...

Powdervalley(dot)com has Remington Large Rifle AND Large Rifle Magnum primers. The also have CCI Larg Rifle BR.

I get it... But why spend $125 on a special die when you already have the sizing die at your bench and all you need to do is remove the decapping stem??

They are both single shots but the seating die doesn't take out the case mouth flare if you cannot roll crimp into the cannelure. As such the loaded round doesn't fall into the chamber. The case rim is actually a few tenths from going flush in the chamber. As far as I know, the Lee Factory Crimp...

I don't like to drop that far down on a powder charge without some kind of wad/filler as you can get wild pressure swings based on how the powder column ignites. While my Ruger No1 would handle that issue, with the TC Encore you could have a barrel blow up on you.

In an interesting twist (reloading master class): if you use bullets that aren't designed for your cartridge. IE: Using 50-110 bullets for a 500Nitro Express. The cannelure doesn't line up for crimping. Additionally, the seater die is designed for a roll crimp for the cannelure vice a tapered...

I have 2 - 500 Nitro Express rifles, a custom Ruger No1 and a TC Encore. The TC Encore needs a lighter recoiling round then factory ammo as it comes in at a mere 8lbs and that is vicious with full throttle ammo. I'm playing with some 500gr Woodleigh FP, designed for 50Alaskan or 50-110Win. I...

I'm even less help. I bought a 375 Ruger and had the barrel bored out to 0.423 to make a 404 Ruger. Get what you want and what your wallet supports. 375Ruger ammo and brass, much easier to find. Easier to load down in bullet weight, 250gr for large North American game or go up to 350gr for...

I have a custom Browning A-Bolt in 458Lott. I had a surplus of 458Win Mag brass and have done exactly what you are asking. This has worked extremely well with North Fork SS Bullets as the bullet itself is a little longer by its design of a solid copper shank. I have shot a bunch of 450gr in the...

1 tin of Imperial Size Die Wax goes a longgggg way. Last one lasted well over 5yrs. That's the best sizing lube I've found. A little goes a long way and I've never (knock on wood) stuck a case yet, using it.

To save time in the future.. Setting up your die: fully remove the size button stem. Screw the die into your press and leave a full turn (360°) from touching the shell holder. Lube a once fired (from your rifle) case and set into the shell holder. Run the ram up fully. Take your case and check...

It's been an ongoing wait...Raven Rock has a very large shipment of 404J Norma brass coming. I think they ordered special run quantity. It was supposed to be here in mid-August. I reached out to them mid-Nov and they said it's still coming, they were hopeful it would be here before the year was...

MidSouthShootersSupply(dot)com has Winchester Large Rifle Winchester Large Rifle MAGNUM In-Stock

When I did expansion testing on Hawk Bullets in my 404J, every single bullet separated the jacket from the core. When I contacted their engineer, he blamed it on yaw. Either via bullet alignment to the bore as part of my reloading methods or not enough twist rate. My expansion test is dry...

Superb scope, ideal reticle, great price! Good luck with the sale.

I'm a Swarovski (1st) and Leupold (2nd) for rifle scopes. When I find a Z6 (Z6i) at a good price, it's go time. Recently snagged a Z5i and equally pleased. I will NEVER...not ever again own a Minox (Blaser Corp is parent). Have had issues with 2 out of 3 of their scopes. Their warranty service...

MidSouthShootersSupply(dot)com has Remington Large Rifle and Large Rifle Magnum primers (In Stock)

Precisionreloading(dot)com has ADG 375Rum brass in stock. $117/50

BrunoShooters has Remington 9 1/2 (Large Rifle) AND 9 1/2M (Large Rifle Magnum) primers in stock. Quite a few of each!!!

MidSouthShootersSupply has Alliant Powders in Stock: Reloder 7, 10x, 15, 15.5, 16, 19, and 25 as well as Power Pro 2000.

PrecisionReloading(dot)com just received a huge shipment of Alliant Powder. Rdlr7, 10, 15, 15.5, 16, 19, and 25. PwrPro2000 They have advised due to Nitrocelulous shortages they don't expect to ship more pwder for a while.

They're sold out now. (Rem LRMag primers at Midway USA)

Looks so... custom shop not even listed on their website now. Wonder if they'd just swap the reticle in the repair shop? The illuminated B&C is still listed as available on the site.

Leupold Custom shop. But you pay full MSRP.

My mistake - retained weight was 336.1gr

I'll dig through my expansion test photos. I have a 400gr Woodleigh SN, loaded to 2160fps muzzle velocity. Did an expansion test at 50yds. Test was dry magazine, pine 2x4, 5 water jugs to stop. (Had 3 more water jugs just in case - to capture the bullet.) Memory serves it came out at 360gr+/-...

No.. That's a ridiculous asking price. There are far better options at that price point.

Going to run these in my 325WSM (Montana Rifle Co X2) let's see if we can find a nice Elk/Moose load.

I'll take them! PM Sent

MidwayUSA just got in Remington 9 1/2M (Large Rifle MAGNUM) Primers. $120+$23Hazmat and limit (1) brick per order. Steep but if you really need them...

Just looked again 1# and 5# shows available and allowed me to add to my cart.

PowderVally(dot)com got a shipment in from Alliant. Reloder 7, 10, 15, 16, 19, and 22

A-Frame 0.423 - 400gr, 0.458 - 450gr.

I have a Swarovski Z6 EE 1-6×24 on my custom bolt and Nikon Moarch African 1-4×24 on my single shot. Both have the German #4 reticle

If the deal falls through, I'll take it.

Any chance you have 1 of these for sale still???

Did SSK Industries do your 470?