Interesting alteration to mod 70 tang

interesting yes, but you have to ask "for what end"?
the answer seems to be "because you can"
what this modification in fact achieves is to drastically reduce the bedding surface a thing that is pretty minimal already.
it would also make bedding harder, as the cutouts at the sides would need clearance in order not to split the stock.
it might also alter the profile where the top of the pistol grip starts making the pistol grip too tight for an ideal hunting rifle.
bruce.
 
Wow that makes about as much sense as pockets in you shorts!
 
I can see the purpose of this operation it removes a knife edge surface which would have no added strength with bedding material and adds a perpendicular surface that that is .125-.150 inch to allow contact with glass bedding material. I seem to remember reading that some model 70’s were splitting stocks this would go a long was to stopping this by almost doubleing the surface area. Just my opinion though.
Shawn
 
shawn,
it is that perpendicular surface that needs clearance on the bedding to avoid splitting.
bruce.
 
Looking at that tang before the it was milled the only portion that was suitable for bedding would be the lug under the knife edge. This would allow more surface for glass contact. I have seen tangs done two ways with clearance and with wood removed and glassed in. If it’s to be glassed in it should be done same time as recoil lug up front. I left clearance on my latest build Mauser 98. Some people see that little gap between wood and metal and assume it’s poor wood to metal fit so to keep a tight fit they will glass that area. Which adds strength to help with splitting. The wood to metal fitting in that area needs to be perfect or have clearance or be glassed if not the tang turns into a splitting wedge.
Shawn
 
if I read you correctly re the knife edge, you bed underneath there, out to the edge, but the knife should be just above the bedding.
this is what gives a bigger bedding surface to the rear tang.
not having a vertical surface is actually an advantage.
any vertical surfaces in this area should have clearance to protect the stock.really the only vertical surface in contact with bedding should be the rear of the recoil lug.
front,sides and front of the recoil lug should have clearance.
tape is your friend when using epoxy.
use it anywhere you need clearance.
whatever you do, no vertical surface in the tang area should contact, epoxy or no.
the thickness of epoxy used will not stop splitting.
bruce.
 
My OWN Winchester Model 70 in .375 HH Magnum had a split stock while my Granddad was the original owner of it in the 1960s. It's been repaired with ( what looks to me like ) plus minus epoxy and stove bolts . I always thought the lack of crossbolts had something to do with it .
 
You must log in or register to reply here.

Members online

... and 1093 more.
Total: 14,764 (members: 1,143, guests: 13,621)

Forum statistics

Threads
53,992
Messages
1,142,637
Members
93,367
Latest member
ChadwickTo
 

 

 

Proudly sponsored by

Latest posts

Latest profile posts

C
Cwoody wrote on Woodcarver's profile.
Shot me email if Beretta 28 ga DU is available
Thank you
•••
P
Pancho wrote on Safari Dave's profile.
Enjoyed reading your post again. Believe this is the 3rd time. I am scheduled to hunt w/ Legadema in Sep. Really looking forward to it.
•••
HENRY GRIFFITHS SAFARIS
HENRY GRIFFITHS SAFARIS
check out our Buff hunt deal!

Buffalo Hunt with Henry Griffiths Safaris $10000

Here with is our offer for a hunt of a...
www.africahunting.com www.africahunting.com
•••
HENRY GRIFFITHS SAFARIS
HENRY GRIFFITHS SAFARIS
Because of some clients having to move their dates I have 2 prime time slots open if anyone is interested to do a hunt
5-15 May
or 5-15 June is open!
shoot me a message for a good deal!
•••
D
dogcat1 wrote on skydiver386's profile.
I would be interested in it if you pass. Please send me the info on the gun shop if you do not buy it. I have the needed ammo and brass.
Thanks,
Ross
•••

Share this page

 
Top