45-70 Lever Action Hi Intensity Loads

One last thing I will add. I wouldn't use Buffalo Bore's or Double Tap's, or any of those boutique manufacturers velocities as completely doable for the handloader... sometimes they are. But all too often, Buffalo Bore and other manufacturers have access to canister powders or powders not available to reloaders which can be tailored to specific characteristics of a specific cartridge. The powders available to us are designed to be as versatile as reasonable and that is why they are jack-of-all-trades, master-of-none. So you may be able to get close but don't be discouraged if you can't match Buffalo Bore's ballistics. Plus, as mention before in this thread. even at 1,700 fps these bullets will effectively take any game in North America and any plains game in Africa!

ChrisG>
You also need to recognize the 45-70 has taken Cape Buffalo and Elephant by both Hunters and PH's who've used both commercial and their own reloads!

I am a physicist with much reloading experience. And, what I've learned is we all try to find the limits these technologies offer. But, I never get discouraged... I set goals and, within the limits of Safety and Reliability, always reach them.

As I develop these 450gr, 45-70, Cast and FMJ loads, I will report progress here at Africa Hunting. I own an Oehler 35P Proof Chronograph and will soon have a Pressure Trace Internal Ballistics System to capture Chamber Pressure.

However, the best advice I've received about my 450gr goals was from Crusty Deary Ol Coot on the Marlin Firearms Forum. Essentially, I raised the issue we all face at the start of a reloading project: with which powder type and charge do we START ("Starting Load") that is not too small as to be a (dangerous... at least via Parker Ackley Vol-1) reduced load?


CDOC's answer was great. Only we 45-70 Lever Action guys have a major resource at our disposal... all those published Starting Loads for the low power Trap Door Rifles are available across more than 10 bullet weights (including 450gr) and a wide range of powder types. The 50th Lyman Reloading Manual, 4th Lyman Cast Bullet Handbook and the 2nd Edition Lee Reloading Manual... ALL list these lower-power Trap Door Rifle Loads. The trick is to realize that a MAX Trap Door Rifle Load can also be the STARTING Load for the higher-power 45-70 Lever Action because COAL is identical for both 45-70 Trap Door and Lever Action cartridges. And, any FMJ load can be used to load a Cast bullet (of the same bullet weight), since an FMJ bullet is longer than the same weight Cast bullet!

Nuff said. Will keep Africa Hunting posted on progress to develop 45-70, 450gr Cast and FMJ loads for my 1895DRC rifle. I'll eventually try solid bullets after these Cast and FMJ load developments.

Bill
 
Last edited:
I just started hand-loading BTB 425 gr Piledriver, Juniors. 37.7 gr RL-7 gets me to just a hair under 1500 fps, accuracy out of my 1895 GBL is astounding.

50 yards with an aperture sight, 5 shot group, 3 touching.

1900 fps, I agree with the rest of them...that sounds very optimistic, and ballistically, with those fat, low-BC bullets, doesn't improve trajectory/range by more than about 30-50 yards MPBR for a 12" vital zone. If your rifle can handle it, and your shoulder can take the beating, more power to you, but out of that rifle and at 1500 fps, I take quite a beating (even with a Limbsaver) with the PDJs.

Beartooth bullets has fairly extensive documentation on their 525 gr Piledrivers, published velocities and powder loads, etc. The hottest load they have listed is 44.3 gr RL-7 at 1705 fps, with IMR3031, 42.8 gr, just behind it at 1683 fps. Note that these velocities are indicated with a 22" BBL. All loads published for the 525 gr are under 40K PSI.

PDs and PDJs are hardcast, BH of something like 22 or 23, and gas-checked. Meplat is in the neighborhood of .36 - .38. They also make a 350 gr PD. Bullet profile is identical for all 3 (350, 425, and 525 gr). I think goosing the 350s to 1900 or even 2K fps is do-able.

Hmmm...having a hard time linking the BTB page here. Google search for beartooth bullets pile driver load data and it should come up.

The *only* gripe I have about BTB is that they're really popular, and the owner still pours the bullets like he always has, which translates to 5-6 months' lead time.
 
Last edited:
Also, consider how many American bison were killed in the late 19th century with 405 gr soft lead or 405 gr paper-patched bullets, with MV in the 1200 fps neighborhood. I expect American bison are as tough as any other 1500-2K lb ruminant, probably tougher than everything but cape buffalo.
 
Own a Marlin 1895 (45-70) updated to a Take-Down by David R Clay (DRC), with a:
- 19.5" Badger heavy barrel hexagon,
- Sights... Scout-mounted Leupold, Ashley Emerson Ghost Ring,
- DRC Glove Lever,
- (Great!) DRC Trigger
- Stainless Steel Magazine Follower.

QUESTION: Develop a load using an Alaska Bullet Works, 450gr Heavy Copper Full-Jacketed, Bonded Core of super hard cast, heat treated, lead alloy (Tin, Antimony). Like to work-up to near 1,900fps. Assuming IMR3031 powder, any idea where to start powder weight?

Bill

In my Marlin 1895 Guide Gun 45-70
350 FNGC hard Cast with 51.8 of RL 7
Sure is a good load for busting bear /moose shoulder blades . It’s a 2000 FPS load.
 
  • Like
Reactions: crs
Update!
Since last post, I have become the proud owner of a Berretta .45-70 double rifle! The previous owner hunted with it and it came with 100 loaded rounds, 100 primed brass, and load data. Here is a picture of the gun and one of my first boar taken with it. It puts a L&R in about one inch at 50 yards, so if there is a miss, it is the shooters fault!



One 300 grain bullet did the trick.
 

Attachments

  • 55185_600x400.jpg
    55185_600x400.jpg
    290.8 KB · Views: 146
  • 54679_600x400.jpg
    54679_600x400.jpg
    101.7 KB · Views: 146
  • 54676_600x400.jpg
    54676_600x400.jpg
    62.5 KB · Views: 155
Last edited by a moderator:
@Bill Conrad

hey bill,

i have loaded for the 45-70 and the wild west 457 magnum (both are the same) and used alaska bullet works bullets 350 gr. as well. i have some loads that are close to your wish list, buuuut, not in a jacketed bullet but a hard cast bullet. if you PM me, will share the load data i have,

don
 
One more note for Bill Conrad -
One of my mentors in reloading big bore straight cased boomers founded and operated a premium bullet manufacturing company where he did extensive testing of his bullets in many calibers and with many different powders, primers, brass, etc. He is the person that first confirmed what my chemist older brother first told me years ago - VV N133 may not always provide the fastest load possible, but it will ALWAYS provide the lowest peak pressure load in the operating velocity range of the cartridge.
The energy curves from Pressure Test II show the N133 pressure curve with no spikes and they also confirm the fact.

My mentor also told me to use a 24 inch drop tube to assure even powder compression and I do that on ALL my heavy loads with .405 WCF through .45-90. He said to slowly count to 10 (10 seconds) when pouring each pan of powder (which was measured to be exact with less than 1/10 grain deviation). This tends to produce loads with very little velocity deviation.
 
Sgt Zim
This thread is an oldie but goodie and your comment on shooting Bison reminded me of one that I shot with our 450 grain African loads. This was all filmed but the best part was when the bison came loping from behind the trees from left to right about 50 yards out.
Foe some reason, I remained composed and put the barrel sight on the beast, tracked it (synching my tracking speed with the Bison's speed) moved the sight picture forward to the shoulder and held for another synch, and then touched off the shot AND followed through as on a sailing dove. I was shooting with both eyes open and saw the shoulders give way, legs buckle, and the beastie roll head over heels to land motionless in the dust.

As expected, the 450 grain NF flat point solid had broken both shoulders and was on its merry way to parts unknown. Love those North Fork Bullets!
 
Randy,
No, I have not heard , but maybe someone will see your query and comment.

Or you could send him a PM and ask.
 
Last edited:

Forum statistics

Threads
53,616
Messages
1,131,183
Members
92,671
Latest member
MorrisFloc
 

 

 

Latest profile posts

Impact shots from the last hunt

Early morning Impala hunt, previous link was wrong video

Headshot on jackal this morning

Mature Eland Bull taken in Tanzania, at 100 yards, with 375 H&H, 300gr, Federal Premium Expanding bullet.

20231012_145809~2.jpg
 
Top