Pressure sign question

YancyW

AH elite
Joined
Sep 5, 2017
Messages
1,649
Reaction score
3,362
Location
Mid-Missouri
Media
9
Hunting reports
Africa
2
Member of
NRA, SCI, RMEF, Ducks Unlimited
I am not an expert by any means, but I am thinking this one might be a bit hot.

IMG_2227 copy.jpg
 
Last edited by a moderator:
Oh man.:confused: And that's a real wack of powder
 
Wtf

Get headspace checked by a gunsmith immediately. Something is terribly wrong.

I am, the rifle is a custom build by Bob Beck, I am going to send it back to him. I have about 300 rounds through the rifle, it has run fantastic until this happened this afternoon.
 
with 300 rounds through it I am surprised that if it were a headspace issue, damn well has signs of it though. Could be a mixture of a few things with all the stars aligning to create a perfect storm. A severely out of spec case maybe combined with a slightly out of spec chamber. Was this round loaded from the magazine? Could the bullet have setback into the case during recoil then fed into the chamber? Set to far out and the mono metal bullet buried in the lands? Whatever it was, pressure was substantial, glad you and your rifle are in one piece.
 
If you have 300 rounds thru it. It’s an ammo problem. Bob loves Bergers. Try some of them.
 
Wow
Had you fired any rounds from this same box of ammo prior to this one? Or was this the first out of the box? Have you shot this same ammo before?
Agree with post above, 300 rounds and no issues then this. Seems more like an ammo issue.
Let us know how this shakes out (y)
 
  • Like
Reactions: lcq
If you have 300 rounds thru it. It’s an ammo problem. Bob loves Bergers. Try some of them.

210g VLDs is what I have mostly shot, but I was going to take it to Africa next month, so I was trying out something different.
 
Wow
Had you fired any rounds from this same box of ammo prior to this one? Or was this the first out of the box? Have you shot this same ammo before?
Agree with post above, 300 rounds and no issues then this. Seems more like an ammo issue.
Let us know how this shakes out (y)

First round. Needless to say, I decided to stop at that point.
 
It did.

The kicker is, this was factory ammo. Barnes LRX 190gr.

These days I'm very leery of Barnes factory ammo as the company is no longer under Barnes control and QC isn't the same. I bought a box of 7mm ttsx 150gr and they were a mix of brass and silver primers. So much for lot to lot consistency. If it is good with other ammo then you should send that box back to Barnes because it looks like a case for recall. Factory ammo is invariably loaded conservatively (lawyers) and that round with the blown primer and ejector mark looks really hot
 
Check OAL on your bergers and on the ttsx loads. Check your chamber with a bullet comparator. I’m interested to see what those numbers are.
 
That is definitely too hot. The blown primer might be a sign of excessive head space, but you also have a lot of brass that flowed into the extractor cutout (I am assuming this is a push feed by the look of it). Cartridge brass usually doesn't start to flow until you get up to around 80,000 psi. I would call Barnes, send them the lot number on the box and the blown case and tell them what happened. It is also possible that this particular piece of brass was never hardened the way it was supposed to be. Did it stick in the chamber? Too soft of brass will do this same thing at normal pressure.
 
Too hot no doubt. Maybe the perfect storm of variables. The most likely may or may not be the reason and it will be difficult for anyone to admit a fault or problem.

IMO- may be something like not enough clearance in neck or throat and/or throat (freebore) is too short. Some ammo seems ok and shoots well as hot ammo many times does... then a type of ammo that may be running at upper end of perssure coupled with a type of bullet, that if stuck into lands, will increase pressure- perfect storm.
 
That is definitely too hot. The blown primer might be a sign of excessive head space, but you also have a lot of brass that flowed into the extractor cutout (I am assuming this is a push feed by the look of it). Cartridge brass usually doesn't start to flow until you get up to around 80,000 psi. I would call Barnes, send them the lot number on the box and the blown case and tell them what happened. It is also possible that this particular piece of brass was never hardened the way it was supposed to be. Did it stick in the chamber? Too soft of brass will do this same thing at normal pressure.

Yeah, you can see where the extractor pulled the rim of the casing. Just under MAG on the case.
 
Yeah, you can see where the extractor pulled the rim of the casing. Just under MAG on the case.
Sorry I meant ejector cutout.
 
WOW!!!!! I would contact the ammo company real quick and in a hurry. If there is any damage to your rifle, I would let them know as well and have them reimburse you.
 
I am not an expert by any means, but I am thinking this one might be a bit hot.

View attachment 224819
I had a similar issue with factory sako ammo in my 300wm.
2 rounds out of a box blew the primers out.
the rest of the box was fine, shot them out and another box or two with no further issues.
 

Forum statistics

Threads
53,634
Messages
1,131,645
Members
92,723
Latest member
edwardsrailcarcom00
 

 

 

Latest posts

Latest profile posts

Early morning Impala hunt, previous link was wrong video

Headshot on jackal this morning

Mature Eland Bull taken in Tanzania, at 100 yards, with 375 H&H, 300gr, Federal Premium Expanding bullet.

20231012_145809~2.jpg
 
Top