Rifle Barrell?

Krieger!...all the time. I think they're the only barrel maker left to produce barrels with the single-point cut-rifling process.

There are quite a few makers of cut-rifled barrels other than Krieger in the USA -- Bartlein, Brux, Rock Creek, Hawk Hill, ...

Benchrest records are held by a mix of cut-rifled and button-rifled barrels. I've good and not-as-good barrels of both sorts.
 
I have a preference for the current crop of 5r cut rifled barrels. These use 5 grooves instead of 4 or 6, which avoid pinching the bullet between opposing lands. An odd number of grooves decreases bullet deformation, reduces pressure spikes and theoretically at least allows higher velocities. The last two rifles I've had built with them, a .280 AI and a .375 HH have borne this theory out with superb accuracy and velocity gains of up to 100 fps with factory loads, though this is far from statistically conclusive I've talked with many customers that have had the same result. With the .280 I've shot several 1/2" groups at 200 yards using 160 Accubonds at 2900+ fps, including one off the roof of my PH's truck.

I believe Boots Obermeyer pioneered their use on the military M40 / M24 sniper rifles back in the 70's. He also trained several of the other popular barrel makers including Mike Rock at Rock Creek Barrels.

These days it's more a matter of who has what in stock with barrel manufacturers sometimes running a year behind, so this more often than not dictates the supplier used.
 
Thanks for replies just trying too figure out if any certain Barrell maker is better for big bore stuff because there's some that excell at bench rest and just trying too find out if there's any that excell at big bore
Danny Pedersen at Classic Barrels in Prescott. I have a .411, .458, and .510 that he made in addition to 2 308's a .257 and a .358. All shoot under .5 MOA except the .510. It isn't finished yet. I expect it to be as good as the rest if it doesn't beat me into submission.
 
I have a preference for the current crop of 5r cut rifled barrels. These use 5 grooves instead of 4 or 6, which avoid pinching the bullet between opposing lands. An odd number of grooves decreases bullet deformation, reduces pressure spikes and theoretically at least allows higher velocities. The last two rifles I've had built with them, a .280 AI and a .375 HH have borne this theory out with superb accuracy and velocity gains of up to 100 fps with factory loads, though this is far from statistically conclusive I've talked with many customers that have had the same result. With the .280 I've shot several 1/2" groups at 200 yards using 160 Accubonds at 2900+ fps, including one off the roof of my PH's truck.

I believe Boots Obermeyer pioneered their use on the military M40 / M24 sniper rifles back in the 70's. He also trained several of the other popular barrel makers including Mike Rock at Rock Creek Barrels.

These days it's more a matter of who has what in stock with barrel manufacturers sometimes running a year behind, so this more often than not dictates the supplier used.


Remington made their own barrels for the original M40 at least. There had been rumors that Hart made their barrels because of the little heart shaped stamp on the barrels, but they are Remmie. Later models cant say for sure.
 
I did a little research and find according to Peter Senich who has written several books on the subject of sniping and the rifles used - both the original M40 and the later A1 used a barrel of 6 grooves. The M40 had a quicker 10 inch twist and the A1 the 12 inch twist. The A1 barrels were made by the Atkinson Barrel Co., when it went into production.
 
I did a little research and find according to Peter Senich who has written several books on the subject of sniping and the rifles used - both the original M40 and the later A1 used a barrel of 6 grooves. The M40 had a quicker 10 inch twist and the A1 the 12 inch twist. The A1 barrels were made by the Atkinson Barrel Co., when it went into production.
FYI: Much of the machinery and tooling that was Atkinson's is still in Prescott either with Classic barrel or at Wells Sports Store.
 
Krieger!...all the time. I think they're the only barrel maker left to produce barrels with the single-point cut-rifling process. I also believe more matches are won with Krieger barrels than any other. They are the best there is. The others mentioned are vey good too....don't get me wrong. But, I think Krieger is at the top of the list.

+1 have 300 H&H and .404 Jeffery with Kriegers - Wonderfully accurate with almost any load.
 
Lilja is a name to be reckoned with these days. Seen lots of match rifles with them including State champs.
 
Among the top barrel makers you can pretty much just close your eyes and pick one. Thay all make great barrels and every once in a great while they all will make a bad one. McGowan and Pacnor are really well known for big bore barrles..............

Some of the "match winners" mentioned above make very good barrels in .243 and .308 but don't make nearly as many many above .308 or .338. My first .338 edge was built around a Krieger and I never could get that rifle to shoot right. My PPC wears a Krieger and I really have to work to get a bad group out of it.......


.
 

Forum statistics

Threads
53,618
Messages
1,131,277
Members
92,675
Latest member
jhonmark007
 

 

 

Latest profile posts

Impact shots from the last hunt

Early morning Impala hunt, previous link was wrong video

Headshot on jackal this morning

Mature Eland Bull taken in Tanzania, at 100 yards, with 375 H&H, 300gr, Federal Premium Expanding bullet.

20231012_145809~2.jpg
 
Top