Results 1 to 3 of 3

Narrow Escapes 2

This is a discussion on Narrow Escapes 2 within the Humorous Jokes, Stories or Pictures forums, part of the GENERAL category; OK so we're on another fishing trip off shore from Los Angeles. My buddy likes to fish deep for Rock ...

  1. #1
    Cliffy's Avatar
    Cliffy is online now AH Elite
    Joined
    Sep 2009
    Posts
    1,066

    Hunted Hunted Zim, RSA (2), Namib(2), going again, Calif, Oregon, Arizona, Texas, Virginia, Idaho, South Dakota, Montana, Nevada, MO

    Cliffy has no Articles
    View Cliffy's Photos

    Default Narrow Escapes 2

    OK so we're on another fishing trip off shore from Los Angeles. My buddy likes to fish deep for Rock Cod. I mean deeeep! 600 to 900 feet!. So we wind up half way to Catalina Island, in the middle of the shipping lanes (did I mention that)? Fairly calm day, 3 foot swell no wind waves. We pull up our lines and he starts the motor. Now you need to know Gary. Gary only knows 2 throttle positions no matter what boat he's in. On and Off! No in between.
    So what does Gary do when it starts? Slams the throttle forward trying to bend the knob off, Damn the torpedoes, full speed ahead! Can you guess what happens? Full RPM NO forward movement. He shears the props shear pin.
    So I says to myself, Self, we're in a world of crap now. I ask him where the spare shear pins are and he says, "What shear pins"? It's his boat but he has no spares and I'm dumb enough to 15 miles to sea with him (he ran out of gas once and floated 2 days and 50 miles off shore until a sailboat found him, but that's another story too). I won't go into what we did as airline mechanics at LAX 40 years ago. Anyway, here we are stuck and now what to do.
    I remembered an old article I read in Popular Mechanix magazine when I was about 12 years old (20 years earlier) about what to do if this happened. My mind is filled with lots of junk info. It said that the pin breaks in 3 parts. 2 smaller outside pieces and 1 longer inside piece and if you unscrew the shaft nut and carefully remove 1 out side piece and push it in on the other side that would allow the longer inside piece to drive the prop.
    So we're in 1000 ft of water and I'm hanging over the stern working on the prop nut knowing if I drop it we drift till our bones bleach. As luck would have it, I was successful and I drove the boat back home slowly. I would have cut his arm off if he reached for the controls! We're still friends to this day.
    IF YOU GO ONCE-YOU WILL GO AGAIN-DEAL WITH IT

  2. #2
    bluey's Avatar
    bluey is online now GOLD SUPPORTER
    Joined
    May 2012
    Posts
    1,996

    Member of ssaa, aba ,bairnsdale field archers

    Hunted australia south africa (limpopo) canada (b.c)

    bluey has no Articles
    View bluey's Photos

    Default

    always the way with boats cliffy its usually the small things that get overloked in the spare parts department .
    but nearly always theres a remedy that saves the day thats so simple you cant always see it .
    luckily you have one of them good memories mate .
    but not to have any shatter pins for your outboard is pretty funny when l think about it specially when your that far off shore in a dinghy .

  3. #3
    Ole Bally is offline AH Enthusiast
    Joined
    Sep 2011
    Posts
    494

    Hunted Zimbabwe

    Default

    Cliffy, you and yr buddy should come over here for some proper PH training! We'll teach you....Never leave anywhere without your leatherman, a piece of wire, some 'avon strap' and a 'shifting sixteeths' spanner otherwise known as a 'Portuguese micrometer'!!

Similar Threads

  1. Narrow escapes...
    By observe in forum Humorous Jokes, Stories or Pictures
    Replies: 43
    Last Post: 05-12-2013, 09:36 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •