Results 1 to 7 of 7

CZ550 ejection issue

This is a discussion on CZ550 ejection issue within the .375 & Up forums, part of the HUNTING EQUIPMENT, FIREARMS & AMMUNITION category; Hello all, Recently, I bought a CZ 550 Classic Magnum in .416 Rigby. Although I've yet to fire it, what ...

  1. #1
    mr50bmg is offline New Member
    Joined
    Aug 2010
    Posts
    1

    Member of NRA IHMSA

    mr50bmg has no Articles
    mr50bmg has no Photos

    Default CZ550 ejection issue

    Hello all,

    Recently, I bought a CZ 550 Classic Magnum in .416 Rigby. Although I've yet to fire it, what I observe is that, upon loading three rounds into the magazine and attempting to cycle the action, the extracted round is not getting ejected. Rather, when the bolt goes fully rearwards, the extracted round gets cocked nose-upward at an upward angle, jamming between the top of the receiver and the upcoming round.

    Pulling the bolt back very forcefully sometimes works, but, obviously, I need it to work all the time.

    This happens with the first two rounds; the last one always gets ejected succesfully.

    Has anyone experienced this? Will it get better over time by cycling the action over and over (I seem to recall someone saying the CZ's get better over time)?

    My brass also gets scratched, too, but that's a minor issue right now.

    Thanks in advance,

    Dave

  2. #2
    sestoppelman's Avatar
    sestoppelman is online now SILVER SUPPORTER
    Joined
    Apr 2010
    Posts
    2,197

    Member of NRA, NA Hunt Club

    Hunted Tanzania, Botswana, Zimbabwe (2), Namibia, South Africa

    Default

    Using live ammo with bullets may be the problem, the 416 is pretty long. You need to shoot the gun and see how empty cases eject. The CZ is a fine rifle, I have two; one in 9.3x62 and a 404 Jeffery. Overall length of the ammo could be an issue. Are you using a handload or factory ammo to test with? Some guys with these rifles note that when cycling an empty rifle that the bolt sort of hitches up at the beginning of the stroke, and mine do as well but not when cycling rounds. If nothing else CZ has very good customer service and will help you out. Hope this helps. Scott

  3. #3
    kingcorona is offline AH Member
    Joined
    Sep 2011
    Posts
    34
    kingcorona has no Articles
    kingcorona has no Photos

    Default Hmmmmmmmmmmmmm

    Your problem brought back a memory of reading an article on ejection problems with some old time calibers in a bolt action rifle.....I remember had todo with the beefy rim getting hung up on the next round in the magazine.....if I remember right...and this was a while ago...try to front load in the magazine the first round then put the next back of that one....since it's a Rigby doubt if you can load more than 3 in the mag......this will allow for a longer throw distance for the ejector to do it's job....just a thought.....there is a tendency to back load the first one then the rest stack up in front....OK with most calibers but not with some.....

  4. #4
    LR4
    LR4 is offline New Member
    Joined
    May 2011
    Posts
    5
    LR4 has no Articles
    LR4 has no Photos

    Default

    Just came back from Zimbabwe and had the same problem with a .416 Rigby Dakota. Ended up using a 375 CK instead for buff. Took 4shots including one double lung and one heart. Used a 470 spinal shot finally.

  5. #5
    LR4
    LR4 is offline New Member
    Joined
    May 2011
    Posts
    5
    LR4 has no Articles
    LR4 has no Photos

    Default

    CZ not CK

  6. #6
    sestoppelman's Avatar
    sestoppelman is online now SILVER SUPPORTER
    Joined
    Apr 2010
    Posts
    2,197

    Member of NRA, NA Hunt Club

    Hunted Tanzania, Botswana, Zimbabwe (2), Namibia, South Africa

    Default

    mr50bmg,
    What did you finally figure out on this? I still suspect that it was a matter of using loaded rounds instead of (firing) loaded rounds and ejecting empties as its supposed to do. The floorplate is the proper way to empty live rounds.

  7. #7
    colorado's Avatar
    colorado is online now AH Veteran
    Joined
    May 2011
    Posts
    176
    colorado has no Articles
    View colorado's Photos

    Default

    I made sure my CZ 550 in 500 Jeffery feeds and extracts dummy rounds flawlessly over and over before I ever took it on a non DG hunt. It took some work on the feed ramp by Wayne at AHR and Kevin Weaver machined my magazine follower a bit. Your rifle should feed and eject full loaded rounds flawlessly or you need it worked on. It should work when you cycle the bolt slowly or rapidly as well.

Similar Threads

  1. Some 7x64 CZ550 Pics for Sestoppleman
    By mlg in forum Up To .375
    Replies: 41
    Last Post: 07-20-2013, 05:08 PM
  2. cz550 505 gibbs and sabatti 500NE
    By Deinotherium in forum .375 & Up
    Replies: 5
    Last Post: 08-23-2012, 01:19 AM
  3. New CZ550
    By Jay Kelley in forum .375 & Up
    Replies: 12
    Last Post: 02-17-2012, 02:03 PM
  4. Deal on CZ550 in 416 Rigby
    By PHOENIX PHIL in forum .375 & Up
    Replies: 12
    Last Post: 08-25-2011, 10:00 AM
  5. Member Login Issue
    By AfricaHunting.com in forum Community Support
    Replies: 0
    Last Post: 09-14-2009, 10:27 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •